| ||||
| ||||
| Moderated by: Greg Fletcher |
|
||||||||||||||
| Late Engine Rear Crankshaft Seal | Rating: 
|
| Author | Post |
|---|
| Posted: 01-20-2014 12:25 am |
|
1st Post |
|
bora450 Member
|
To date, I have rebuilt Triumph TR6, Porsche 944 Turbo and Maserati V8 engines. All of these have shaft seals where the outside surface is pressed flush with the surrounding surface. I am now checking and cleaning 1974 J-H engine parts in preparation for reassembly. The old rear crankshaft seal surface protrudes from the cover plate by .05. I have a second engine with the seal installed identically. The Workshop manual does not address seal installation. I have reviewed all of the posts about rear seals and didn't find any comments about this so I solicit them now. Thanks, Claus
|
||||||||||||||
| |||||||||||||||
| Posted: 01-20-2014 03:13 pm |
|
2nd Post |
|
Brett Gibson JH5 20497 Member
|
Hello Claus, it's very important that you do not seat that rear main seal flush, go with the measurement you got and you should be trouble free, it has to do with just were the seal lip rides on the crank surface and the amount of end float the crank has, in to close and the seal gets eaten. At least you have a later engine and not one of the wrope seal early ones, they are not very forgiving and tend to leak abit more often. Brett
|
|||||||||||||
| ||||||||||||||
| Posted: 01-20-2014 06:20 pm |
|
3rd Post |
|
bora450 Member
|
Thanks Brett, I did notice that the polished area on the crankshaft was close to the block side of the flange so that makes sense. In anticipation that there was a good reason for the seal offset, I machined a .100 thick aluminum spacer yesterday to fit inside the bore. When I press the seal against the spacer it will be in the same place. Claus
|
||||||||||||||
| |||||||||||||||
| Posted: 01-21-2014 07:46 pm |
|
4th Post |
|
Dakota123 Member
|
For piece of mind, you can grease the seal, push the cover/seal into position, then remove. The grease will leave a smear on the flange and you can tell exactly where the seal will ride.
|
|||||||||||||
| ||||||||||||||
| Posted: 06-15-2014 02:02 pm |
|
5th Post |
|
George Member
|
Thought I would resurrect this topic for a quick question. I see the rear seal is offset from the edge of the cover plate, but I am still not entirely clear which way. Is it .100 of an inch further in toward the engine, or .100 proud sticking out the back of the plate toward the rear of the car? Thanks george
|
||||||||||||||
| |||||||||||||||
| Posted: 06-15-2014 05:34 pm |
|
6th Post |
|
bora450 Member
|
The seal should be sticking out .100, away from the engine. I machined an aluminum disk to fit into the recess on the engine side and pressed the seal in until it bottomed on the disk. That way the seal would be straight.
|
|||||||||||||
| ||||||||||||||
| Posted: 06-19-2014 04:18 pm |
|
7th Post |
|
Esprit2 Member
|
The important dimension is that the seal must be recessed 2.5mm (0.100 inch) from the inside machined face of the seal housing. How far the seal ends up sticking out of the housing just is what it is. See the attached JPEG. Attachment: 9XX Main Seal Housing - Rear - Installation into Housing, 2.5mm, 84kb.jpg (Downloaded 100 times) Last edited on 06-19-2014 04:19 pm by Esprit2 |
||||||||||||||
| |||||||||||||||
| Posted: 06-25-2014 05:23 pm |
|
8th Post |
|
George Member
|
Thanks everybody !
|
|||||||||||||
| ||||||||||||||
| Current time is 05:10 am | |
| > Jensen Healey & Jensen GT Tech > Engine & Transmission > Late Engine Rear Crankshaft Seal | Top |
