Ah. When all else fails read the directions ! I didn't realize its a "sealant" too thanks ...   06-30-2014 07:38 pm

hello everyone.  I have seen some postings on the importance of sealing your flywheel bolts to prevent oil leakage, what are people using?  I usually ...   06-30-2014 03:08 pm

Thanks everybody ! ...   06-25-2014 05:23 pm

Thought I would resurrect this topic for a quick question. I see the rear seal is offset from the edge of the cover plate, ...   06-15-2014 02:02 pm

You can also use a semiconductor for the regulator. Its probably easier just to buy a new regulator, I think they are about $20 ...   04-09-2014 01:13 pm

I just bought a parts car 1974 Jensen Healey, and it came with a gas tank that was redone by "Renu" still in the ...   03-26-2014 02:19 pm

Hello all.  Thought i'd revive this discusion as the link no longer works.  Does anyone have a new link to this info on Dellorto conversions ...   11-14-2013 02:55 pm

All but one  look pretty rusted out, but there's a guy on the Ashville, NC craigslist who has three jensens for $1200.  Might be some ...   10-31-2013 08:40 pm

I knew those pads were there, but I hadn't fully considered their implications!  Thanks for the advice.  I'll wait for Andy's thin shims.   g ...   09-06-2013 12:51 pm

Thanks, Andy !  Will do.  I had another thought, would it work to put a sraight edge across the top of the retainer and measure ...   09-05-2013 07:53 pm

Thanks for the idea.  I do have some shims and I thought maybe I could use them to get a measurement as a basis for ...   09-03-2013 09:41 pm

Hi guys.  I got a rebuilt head that looks to be in good shape from someone who didn't know much about it.  Now, I am ...   09-03-2013 08:25 pm

Got it - thanks, Jim. ...   07-11-2013 03:05 pm

Hi everybody.  I am taking the exhaust cam tower off my engine, following Greg's sage advice in the mag.  I turned the drive shaft 90 ...   07-10-2013 02:14 pm

Sorry, but I don't think either of those is the stabilizer.  It is flatter and smaller  than the relays and should have two prongs of ...   07-07-2013 02:11 am

Well guys, here’s the thing.  Bought a Jensen Healey that was supposed to have 14k original miles, when it showed up (I know, don’t buy a car ...   07-04-2013 09:33 pm

Hey guys, I'm back in the JH fray, having just gotten 14473, a 74, from a gentleman near Cleveland. (I'm in Maryland.) The car is ...   07-03-2013 03:42 pm

Glad it worked out for you.  On mine it turned out I cut  it down a bit too far and the cancelling only worked intermittantly, I ...   03-29-2013 01:20 pm

Mine are just lap belts.  Even my kid won't go back there! ...   10-09-2012 12:55 am

Mine were replaced shortly before I got the car and they have stickers on them marked - Service Plus Distributers, Bensalem PA SPD 5300-60A If you are given an ...   07-20-2012 09:17 pm

Hi Frank.  I'll try to take a pic and send it.  It was pretty straight forward.  I cut a piece of metal about 8" by ...   06-12-2012 02:16 pm

Thanks.  That's what I ended up doing as well, painted black too.  It only sticks out about 4 inches, but is well secured under the front ...   05-20-2012 11:45 pm

Hello.  I put a front spoiler on my JH5, really helped with cooling.  It looked good, however, it was kind of big.  Now i need something ...   04-30-2012 07:54 pm

Thanks for the info!  Cut it down and it works great.  I didn't find I needed to modify the slots.   g ...   04-16-2012 03:03 pm

I think the Montana one has Dellortos, wish I wasn't over here on the other side of the country ...   04-12-2012 02:18 pm

Hello everyone.  My GT has, I believe, an MG turn signal switch replacement.  When i turn the wheel the switchs try to turn with it.  ...   04-11-2012 05:39 pm

Hello everyone.  Despairing of ever getting my Interceptor on the road and regretting selling my JH5,  I purchsed a GT (VIN 30242).  Needed a little ...   03-08-2012 03:46 pm

Howdy all.  Long time no post.  Since i bought my JH, the heater has never been hooked up.  The upper hose thru the firewall is ...   10-30-2009 10:11 pm

I just got my copy of the mag, and I have to agree, that is a nice dashboard! ...   04-19-2008 02:49 am

I have tired making a home bleeder and also tried a Mityvac.  All I ever succeed in doing was making quite a mess.  I could ...   04-05-2008 01:34 am

Hey Greg, it would be great to meet you, if you do come.  BTW - Bring a couple Jensen Healeys with you.  You guys have ...   03-31-2008 04:19 pm

I was examining the situation and it seems the spoiler will bolt straight to the panels on the sides where there are already bolts.  I will add ...   03-15-2008 01:30 pm

I look forward to it. Anyone else using spacers?  Any thoughts on their use? Thanks George ...   02-11-2008 01:13 pm

Wow.  That sounds great!  I'd like more info on the adapters (were they expensive/hard to make?) and like to see some pics.  I am just getting ...   02-10-2008 01:30 pm

Someone is listing a GT for sale in the marketplace, where he says he took out the 5 speed and put in a four, you ...   08-21-2006 02:58 am

You can get a cheap (in more ways than one) replacement for the master from Victoria British.  You probably get what you pay for, but ...   08-09-2006 05:26 pm

Oh dear, quite an intro to our wonderful cars.  Plenty of info on this site, however, to help you out. Just ask.   Welcome.  Where are you located? ...   08-07-2006 12:00 am

I ignored my brake light issue, then ended up having to change the master.  After I replaced it, the light was out with no balancing ...   07-11-2006 02:07 am

I have one of the Thai jobbies sitting on my kitchen counter for installation tomorrow and it does not have the notch out of it.  ...   05-17-2006 03:02 am

Wow, that looks great, but I am still happy with your 4 core cast off.  Fit right in and seems to do the trick.  I ...   05-07-2006 01:29 am