Both cars burned in Tubbs fire, Santa Rosa, CA, Oct 2017       One was a race car 17418, the other a donor 13714.      Farewell little buddies. ...   08-03-2020 04:44 pm

Thanks for the information.  Unfortunately the car (both of them) burn in the Santa Rosa Fire.  I was able to salvage the rotors, and they ...   03-28-2019 01:51 am

I went the full route. I had a bit of rust on the floor so cleaned it up, used POR15 and repainted. Then ...   03-17-2017 10:09 pm

Do you by any chance have an under pad for either side?  Thanks. ...   03-17-2017 09:59 pm

I have a 5 speed as well with no JH5.  Vin is 19714 purchased in Oakland, Calif by me.  I wonder if that was a ...   07-19-2016 12:22 am

That comment must have been meant for a different thread.  It doesn't makes sense here.  but curious as to what you are talking about? clif ...   06-23-2016 04:22 am

Sorry.  Was talking about the cover, not the tower itself. Clif ...   06-18-2016 04:37 pm

Upgraded my JH to a full 2.2 conversion.  I did "have" leaks from the cam towers, but put a proper torque on them and the ...   06-17-2016 07:55 pm

Not sure if this is a continuing thread but... I checked my shock and it has a number that is different than either of the two ...   05-11-2016 05:29 am

What a great little car to race.  But in 24 Hours of Lemons???  Are we crazy? Nope.  With a couple of years of Lemons racing ...   07-17-2015 07:27 am

Hi all. I hope this helps.  I was looking for an answer to this question myself.  I had a shop try and they gave up so ...   07-10-2015 10:57 pm

Not much chance you still have the springs and shocks, but if you do I am very interested. Just started a 24 hours of lemons and ...   06-30-2015 02:29 am

JH #19642 Engine No. B74 12 10 579 Purchased May 2015 in Sebastapol, CaThis car is no more.  It burned in the Santa Rosa fire in ...   04-26-2015 08:13 pm

Been a while since there was any talk about this. I had Huffaker rebuild my front end and just checked. To confirm, the flat side does ...   03-26-2015 02:10 am

Thanks.  I got it out.  I had done this before and there was already some tearing in the corner, and I have noticed this in ...   11-14-2013 01:15 am

Easy question.  How do you remove the plate on the steering wheel to access it's mounting?  I need to replace the turn indicator. Thank you Clif ...   11-12-2013 08:58 pm

FYI. Mine is the 2.2 high compression, 104 cams, Pertronix, adjustable cam pullys....all the good stuff. And it seems we have had this conversation before. The below information ...   11-12-2013 02:26 am

Nope.  It is for sure a spring loaded gizmo of some sort and it won't release even when pushed all the way in.  Glued...I don't ...   11-12-2013 01:45 am

I still don't have an answer for wet or dry when it comes to torque on the flywheel bolts.  Anybody have an answer? Here is the ...   10-10-2011 04:40 am

Just a quick note on your install. Check the joints.  This is a bolt together system.  Mine was installed for me by people who claimed to ...   08-04-2011 01:10 am

I couldn't take it any more.  The Delta exhaust was a terrible fit, hitting the axle and leaking, and was way to loud.  I finally ...   08-03-2011 05:01 am

Thanks guys, but what to use isn't the problem.  It's how do you get it into the hinge? I just tried using a piece of 1/8 ...   07-28-2011 01:47 am

Since I was unable to find a way to lubricate the door hinges other than removing the doors, I decided to open a new topic ...   07-25-2011 01:36 am

Have a new lighten flywheel.  (EBAY).  It looks to be new, but I am concerned that everybody, including me has a flywheel with a ring ...   11-30-2010 12:26 am

Hello JensenMan. I know it has been a couple of years since this post, but if you still have your flywheel, would you mind getting back ...   11-30-2010 12:04 am

Not home yet, but it looks like about 3/8 inch has been removed from the back side. The most interesting part is that this flywheel does ...   11-28-2010 01:46 am

If you haven't parted with your damper, I sure could use one.  Mine is shot.  By the way, if a 2.2 is done does that ...   10-15-2010 05:49 am

There is quite a bit of information on the internet.  I googled "torquing bolts" and found all kinds of information.  Seems lubrication is important especially ...   10-04-2010 06:02 pm

This is a lightened stock flywheel.  Probably in the 16 pound range.  I'll get back on that when I get it. Getting back.  Just weighed it ...   10-04-2010 06:20 am

With the full upgrade to a 2.2 is it necessary to change the pressure plate and or clutch to deal with the additional power and ...   10-03-2010 04:34 am

So I just got hold of a lightened and balance flywheel.  I plan to install it during the winter. I have noticed a couple of mentions ...   09-24-2010 05:08 pm

Just hit the general category "Jensen Healey", and the shocks don't show up.  You might have something wrong with your listing. Never mind, it was well ...   08-22-2010 06:14 am

Thanks Norm. But at $700.00 plus shipping from Australia, these are way out of my league.  That's about 10% of the value of a good condition ...   08-22-2010 02:54 am

That address indicates the item has been removed! Sold? ...   08-21-2010 07:41 pm

Thanks Greg. Place them in series where? Clif ...   08-11-2010 08:06 pm

Thanks Gary. Just one thing, well maybe two. The Second Strike Pertronix has six wires.  Black, Red, Yellow, White, Orange, and Green. Their diagram shows: Black to battery negative. Red ...   08-11-2010 01:37 am

Thanks Kurt. However, I don't see anything on the firewall that has a wire connected to it.  Several wire flitting around the coil.  I hear there ...   08-10-2010 04:56 pm

OK.  So I finally figured out what to do via the Pertronix website, but not how to do it. They say "...relocate the tachometer trigger wire ...   08-10-2010 05:31 am

Anybody had this problem? I have the Pertronix ignition system installed and the car runs great.  But now the tachometer show zero rpms.  Even went to ...   08-08-2010 05:30 pm

Does anybody have some current update information on shocks for the JH? Last info was about a year and a half ago and it looks like ...   06-22-2010 07:49 am