I've been using the TR6 backfit for many years but I think it is starting to give me problems so I'm planning to take a ...   01-01-2020 01:35 pm

Thanks Nigel - it appears to be the AAU8994, however the only kits I can find so far are on ebay and extremely pricey (>$100). ...   01-16-2018 07:03 pm

Trying to find set (both wheels) of upper self adjusters & springs for Lockheed rear brakes - anybody have a source or spares? Below is ...   01-16-2018 02:14 pm

I guess that means no 5 speed rear end for me! ...   05-14-2016 12:07 am

I am looking for a 5 speed rear axle with the 3.45 gears. Where are you located? I am in upstate NY ...   05-13-2016 08:28 pm

Converting 1973 to 5 speed Getrag...couple questions: (1) anybody got a pic of how they dealt with the transmission support being shifted ~3" from 4 ...   12-27-2015 06:27 pm

thanks. i was in spec when I installed the liners and they still look good. Planning to go with the JAE ARP stud nut upgrade ...   10-12-2013 12:41 am

After rebuild with high compression pistons and other HP upgrades, head gasket leak after 5,000 miles from cylinder 2 to water jacket. Does anybody know ...   10-11-2013 01:41 am

Looking for a clarification since manual a bit unclear - want to remove the rear casing (4 speed) to replace the gasket. Does something have ...   01-13-2013 07:40 pm

Anybody get a chassis dyno (HP/torque at the rear wheels) done for a stock Jensen-Healey? I'm looking for a baseline HP/torque curve since I never ...   08-16-2012 09:48 pm

I seem to be thru all my issues with the Dell 45's - here's what I did/found...I've attached a pic to help with the explanation... ...   04-21-2012 10:18 pm

I've got the 7850.7's on order to see if that is the cure. I have also come across another issue which shows up when I'm out ...   04-08-2012 07:53 pm

My front seal on the transmission appears to be leaking. The shop manual doesn't discuss how to replace it. Before I pull the tranny and ...   04-08-2012 07:45 pm

Having a problem with significant hesitation between 2000-3000 RPM with my Dell 45's. Idling and >3000 is smooth and strong. Reading the various JHPS posts ...   04-05-2012 12:22 am

There are several bulletins...that were not in my manual. 75-8 and 76-2 address the Oring...if only they told me the material for the ...   01-18-2012 09:16 pm

OK - one last question. What is the proper tube material...Aluminum? ...   01-17-2012 08:44 pm

OIL PAN GASKET - last engine tear down I got some gasket material from NAPA and cut my own. It never leaked. Since you still ...   01-13-2012 09:38 pm

1973 Yellow/Black Interior, Chrome bumpers VIN#13902; Engine B74 11 10 146 Restoration completed 2006 Engine complete rebuild with performance modifications March 2012 (Dellorto 45 conversion, Hi compression +0.030 ...   01-07-2012 04:07 pm

The 74-23 is not in my service bulletin...does someone have a copy they could send/email? ...   01-06-2012 09:04 pm

Problem solved. The solution was simple once I grabbed a beer and stared at it one last time. I've attached a photo as my setup ...   01-06-2012 08:18 pm

Well, I left it out in the convenient 5F temp we enjoyed this morning, then blasted it with a torch and slammed it with an ...   01-05-2012 01:39 am

Anyone had to deal with a aux shaft stuck pulley? I have the female allen style bolt and I've tried heat, liquid wrench, large wrecking ...   01-02-2012 09:43 pm

It's been a half-dozen years since a lot of chatter on engine upgrades, so I wanted to "test" what I am concluding for my rebuild ...   12-21-2011 07:34 pm

thanks. my concern was that some of the attachment options near the starter "look" weaker and I didn't want to risk cracking any of the ...   12-16-2011 12:58 am

Paul - Carol and I sure enjoyed our times together with you and Ellen, in particular the multiple Lake Placid visits and the Kalamazoo trek. ...   12-13-2011 10:06 pm

Got a used engine stand (no instructions) and this is my first use of one of these. Are there preferred bolt holes to use for ...   12-13-2011 10:02 pm

Got that new TR-6 master cylinder and everything working fine for a few days. Then, for no apparent reason, after a 5 mile drive, I ...   05-07-2007 10:17 pm

Thanks - I pulled the master cylinder back out and bench bled after getting tired of exercising my foot. Putting a slight back pressure on ...   04-28-2007 01:13 pm

Winter is over, jumped into my Jensen Healey and brake pedal went to the floor. No brake fluid anywhere. Everything was fine when I put ...   04-25-2007 01:30 am

Hi Tom 13902 may have decent hood alignment but struggles with driver side door/fender alignment. I guess that's each JH having its own quirks & personality. Bob ...   08-19-2006 02:19 pm

closer than I thought - I'm on Garnsey Road off 146 and Blue Barns Road in Rexford ...   08-17-2006 10:16 pm

Wanted to let you know my 1973 is back on the road in Albany/Schenectady area...after a 2 year restoration. Let me know if any of ...   08-16-2006 12:52 am

Mark, Edward...thanks for the suggestions...Well, it took a bit, but problems solved. The fuel pump was putting out over 4 psi and the choke disc ...   08-01-2006 01:46 am

I checked the fuel pressure and it is slightly over 4 pounds...so that appears to be at least part, hopefully all, of the problem. There ...   06-30-2006 01:16 pm

After rebuilding (Delta kits) both Stromberg carbs, and lots of follow-up troubleshooting, I can't seem to solve running rich at idle. Everything was rebuilt except ...   06-25-2006 06:14 pm