Pontiac had aluminum exhaust manifolds available for the SD engines in their lightweight Super Stock full sized cars back in 1962. I think they were ...   12-21-2018 10:19 pm

I have Lloyd mats in my JH. The first set they sent were stitched for RHD. I had to show them pix of what they ...   12-21-2018 10:16 pm

...   09-27-2018 06:15 pm

"With all that it's amazing that such a superior sportscar as the Jensen-Healey was able to emerge." Seriously?? Please don't share that Kool-aid ...   09-25-2018 10:02 pm

Thanks redracer! As to #7 - ("plug" with 1 3/8" drain tubing and solder it to a copper plate) - would you happen to have pix ...   08-29-2018 10:53 pm

Thanks Art! Any other advice, like how many extensions does it take to get to the bellhousing bolts? Do you need to support the oil pan ...   08-28-2018 06:02 pm

Any tips on removing and replacing the transmission on a 74 JH? My clutch is fine, so looking for experience on the easiest removal. ...   08-27-2018 04:29 pm

...   06-29-2018 04:33 pm

Rust Encapsulator from Eastwood is also good. After I cleaned the scale off the front floors, I used it before laying in two plies of ...   03-19-2018 06:19 pm

...   02-04-2018 10:54 pm

finally got my Delta exhaust on . . . ...   02-02-2018 01:05 am

The stock oil drain plug size is Whitworth WW 1/2 in case anyone else has the issue of the proper method of removing it. At ...   09-29-2017 06:06 pm

used a pair of needle nose pliers, worked it back and forth (turns out it is just a steel piece with a hole in ...   09-29-2017 06:02 pm

Thanks for pointing to that for me! I just might have to go that way ...   09-25-2017 08:12 pm

Sorry if I wasn't clear, but I need to get the speedo cable pinion gear out of the tailshaft of the 4-speed Chrysler transmission. The ...   09-25-2017 03:38 pm

How do you get the bearing out, in order to remove the pinion gear? The service manual does not address this at all. ...   09-24-2017 02:18 pm

Mine had a JH AM-FM but the FM didn't work, so I found this NOS Radio Shack Optimus cassette deck with aux input so I ...   09-20-2017 03:45 am

Thanks for the link Steven. Very interesting articles. I'm not sure why but was Jody Kerr involved in this project? He was a Studebaker guy ...   09-08-2017 11:26 pm

Thanks! I'll join today ...   09-07-2017 06:06 pm

I'd like the see the FI article. And a link to the DIS piece also. Thanks! ...   09-07-2017 05:56 pm

the headlight scoop is sitting ON TOP of the bumper. The bumper is too high and too far back. Don't know if you can loosen ...   08-04-2017 07:18 pm

Thanks for the documentation! Very nice drawings and pix. Looks very doable, even by metalwork challenged peeps like me. ...   08-01-2017 04:27 pm

I'd like to see the plans and pix also ...   07-31-2017 03:04 pm

might anyone have a spare trim to go on the rubber? I just looked at my left front, and on my last drive, it must ...   07-24-2017 09:19 pm

Someone should pick this up, it's a steal at that price. ...   07-24-2017 03:44 am

One done. Using MrMike's fiero headless seat kit ...   07-02-2017 06:12 pm

I would have made it, but I thought the spring steel it is made from isn't in my cache of materials. ...   06-15-2017 06:52 pm

I wish you the best inre surgery. ...   06-15-2017 03:03 am

Frank Yes I'm in Phoenix. Not familiar with any British wheel makers. I remember a cycle shop in Central Phoenix that did a lot of the ...   06-15-2017 02:57 am

Hi Frank, No, that pic is actually of the driver's side, and I do need the passenger side. I have the Velcro sleeves, got the kit ...   06-14-2017 11:58 pm

Hi, I was putting in my new seatbelts and noticed that my convertible top frame is missing the right hand upright piece that holds the Velcro ...   06-14-2017 07:25 pm

Thank you! As I was going to put in new needles tomorrow, I will put them back on in the correct direction. ...   05-28-2017 02:00 am

I've only had the car for a few months and they were on it that way before I rebuilt them. I looked inside and didn't ...   05-28-2017 01:46 am

don't know why I couldn't put two pix on the post, but here's the other one ...   05-27-2017 10:28 pm

Never liked the look of the stock airbox (too Hooverish) and I didn't like the look of the K&Ns that the car came to me ...   05-27-2017 10:20 pm

Great pix, glad you posted! ...   05-10-2017 09:19 pm

I realize that this post is way old, but . . . I just put both the inner and outer door window wipes on with adhesive, ...   04-27-2017 01:12 am

Finally got to install the work of art (new tensioner) today. Flennor bearing, Flennor belt, Kent-Moore tension gage. Works like A CHARM!!! ...   04-26-2017 09:33 pm

Thanks! No emission test for this car, classic plates and insurance obviates that in AZ. Will time back to 110/110. I was just checking in here ...   04-11-2017 01:59 pm

Just starting cam belt/tensioner replacement on B74 2 5757 When camwheel marks face each other, intake notch is 110 and exhaust notch is 115 I've heard the ...   04-11-2017 03:01 am