Just cos I like my interior. ...   03-12-2017 09:28 pm

Male part of latch. ...   03-12-2017 09:27 pm

Velcro around cockpit. ...   03-12-2017 09:26 pm

Velcro on door post. ...   03-12-2017 09:25 pm

Female part of latch. ...   03-12-2017 09:24 pm

The top basically just wraps around the frame and is held in place with contact adhesive. the trick is to get it tight enough ...   03-12-2017 09:22 pm

Hi Steve, I live in Eastanollee, Georgia, (near Toccoa) so am not too far from you. You are more than welcome to come and ...   03-12-2017 03:48 pm

Frank, I think I have one out of the owner's manual for a 1972 UK spec. I can dig it out when I get home tonight and ...   11-01-2016 03:30 pm

Frank, The best way I know to be sure you are not 360 degrees out is to remove the valve covers (I know, on a 907 ...   08-04-2015 01:57 am

Frank, I have the luxury of having a lathe in my shop so made them myself. You should be able to find a local machine ...   06-07-2015 03:55 pm

Frank, I removed mine by the same method Clinton used below. A little tricky but doable. I rebushed my own U joints using bronze ...   06-06-2015 04:41 pm

George, I have a set of shims that I had ground to the minimum thickness to use at as a starting point.  Send me your address ...   09-04-2013 12:30 pm

Anyone know where I can find a couple of the hex drive spacers that go behind the window winder.  I remade my door panels a ...   05-08-2012 11:25 pm

I came home from work yesterday and found this on the dining room table.  I think that my Wife is tring to send me some ...   01-02-2012 11:24 pm

Scottm5407 wrote: On both of the assemblies that I have, there is a pilot light with a blue lense at around the 2 o'clock position in ...   12-06-2011 05:45 pm

Driving home from work the other morning, after working a night shift, it was a little chilly so I had the roof up and the heater ...   11-05-2011 04:03 pm

Are you sure that fluid from your old master cylinder didn't leak into the brake booster and that is what you are now seeing leaking out? Andy ...   05-29-2011 04:20 pm

The last time I bought them I went to Advance Auto Parts.  The kid behind the counter asked what I needed and I told him ...   01-29-2011 11:54 pm

Frank, I have John Kimbrough's wiring diagrams (which I have found most useful on several occaisions) but apparently can't post a zip file as an attachement. If ...   07-08-2010 02:08 am

Seems like the attachment was too big.  Send me your email address (to limey01@aol.com) and I'll send it to you. Andy ...   07-18-2009 02:17 pm

Attached is an excert from an from an article I wrote for the JHPS magazine some time back. It might give you some pointers (perhaps on ...   07-17-2009 10:46 pm

Joachim, I did place the axle stand under the sump but with a 2x6 inbetween to spread the load.  It's a little tight, but possible, to ...   09-02-2008 12:38 am

Anyone looking for a reman alternator check this out.  Just follow the prompts for make, model, year, etc.  $92.99!!!! http://www.partsamerica.com/ ...   08-10-2008 02:58 am

This pic shows the plate installed.  Note that I rerouted the wires for the side marker through a grommet in the cover plate.  I also ...   07-14-2008 03:06 am

While driving home from work the aother day in the rain I was quite pleased at how little water made it's way into the car ...   07-14-2008 03:03 am

Thanks Frank! I'll start hunting for one.  I would still like to know the impedance of a good one though. Andy ...   07-08-2008 03:25 am

Thanks Jgreen, Frank, can you point me in the right direction? ...   07-04-2008 03:13 am

Does anyone know the impedence of the rheostat for the instrument lights.  Mine checks out at about 30 ohms but is very erratic.  Thinking of ...   07-02-2008 10:16 pm

Sorry guys, Life has been a little hectic lately.  Will get to it soon. Andy ...   06-04-2008 02:22 am

I managed to reset mine by removing the switch and using something like a ball end allen wrench (don't remember exactly) in the indent in ...   06-04-2008 02:20 am

I've noted since I redid my suspension that I get a whirring noise from the rear end when I let off the gas, none when accelerating.  ...   05-11-2008 07:31 pm

Bill, I wouldn't know where to start to do as good a job as John to post my pictures.  Sure wish I had read his article ...   05-10-2008 03:24 am

If I had my "rathers" it'd be Newcastle Brown, but after buying all those parts, I had to economize somewhere :) ...   05-08-2008 06:04 pm

The attached picture represents about four months of beating, pressing, grinding, cursing, painting, bead blasting, machining, wire brushing, swearing and waiting for the UPS guy ...   05-06-2008 06:39 pm

I seem to remember that on the JH I owned many years ago in the UK, the gearbox would get a little sticky in cold ...   04-18-2008 02:25 am

NAPA 14855 as another alternative. ...   04-17-2008 01:20 am

I whittled up my spacers today.  Picture attached. Andy ...   04-03-2008 12:33 am

I bought mine from Shock Warehouse.  Cheaper on Amazon but Shock Warehouse had free shipping. I was working on fitting the front ones today. For the lower end ...   04-02-2008 05:43 am

I am waiting for two pairs of KYB's to arrive, KG5501's for the front and KG5552's for the rear.  I will post how the installation ...   04-01-2008 02:32 am

Edward, Have you considered putting the gaskets back in under the cam towers?  This would work as a temporary/permanent fix.  It does make setting the clearance ...   03-12-2008 12:21 pm