Thanks for the info. ...   05-12-2023 02:34 am

Thanks for that. I looked around underhood, any idea where the ARV would be hidden? ...   02-16-2023 12:46 am

Two questions that are sort of related: Is there a wiring diagram that is applicable to the 1975 JH available? Don't need a free one. ...   02-15-2023 10:22 pm

Do the four speed and five speed use the same clutch fork? thanks ...   11-25-2022 02:01 pm

hey thanks for that.   It was tedious but do-able.  Helped a lot that I took the seat out.  Didn't have hemostats but was able to ...   05-16-2022 02:52 pm

anyone have any install tips for the throttle cable in the Jensen?  I looked through the service manual but didn't see anything applicable. It looks like ...   05-14-2022 11:43 pm

RE: the LM-2, I found mine to be very sensitive to grounding. I run it directly off the battery and it has always worked well. Otherwise, ...   07-18-2019 02:42 pm

https://spacecoast.craigslist.org/cto/d/merritt-island-jensen-healy-1973/6781320464.html ...   01-18-2019 05:09 pm

thanks..that's very helpful ...   03-05-2018 05:35 pm

Would anyone know the size and thread of the brake line fittings where they attach t o the master? I'm having no luck finding any locally ...   03-05-2018 02:21 am

I actually made 1,000 miles use without getting stuck. I call that a win. Continued my carburetor experiments...had some soot on the body ...   06-01-2017 03:36 pm

bought the distributor from the club store. Very happy with it. Runs very well. ...   04-03-2017 12:13 am

thanks........I will look into that... I understand what you're saying about distributor rebuilders....  I had one highly touted distributor rebuilder tell me in no uncertain terms ...   03-26-2017 09:25 pm

502 bad gateway....I don't know much about computers...can't read posts, don't know what to do ...   03-26-2017 05:06 pm

As the title says, oil in the distributor....engine won't run well at all. Please forgive my lack of familiarity with the 907 platform, but I did ...   03-25-2017 10:34 pm

thanks ...   02-15-2017 12:59 am

Tim, I curious to know what the step up for idle air correctors is. Do you go up one step or two as a tuning ...   02-14-2017 09:54 pm

thanks for the well wishes. Maybe I used the wrong term but the item the exhaust is hitting is mounted to the body above ...   02-07-2017 03:55 pm

Took it for its first ride since 2005 today. Put about 40 miles on. Ran at the proper temp, stopped, turned, idled in traffic. ...   02-07-2017 02:41 am

...   02-06-2017 01:27 am

washed, buffed, waxed...I did not get motivated to install the trunk carpet. DMV tomorrow What does everyone use on the rubber bumpers?  Armor All doesn't really do ...   02-05-2017 10:43 pm

Wheels aligned, going to wash and compound it tomorrow provided it doesn't rain. If I get motivated, I'll even put the carpet kit in the trunk ...   02-05-2017 03:18 am

do you have an air compressor? If you do, adapt the air compressor to the compression tester hose. Bring #1 to TDC. Trans in gear ...   02-05-2017 03:14 am

Thanks for the picture. So the oil filter holds the whole thing together...got it ...   02-03-2017 05:01 am

OK....as an alternative, is the centre of the attaching fitting machined as a hex so as to allow the use of an allen wrench to ...   02-03-2017 02:36 am

thanks, to make sure I understand you; on the side that the I screw the oil filter, there will be a hex that I can ...   02-03-2017 12:21 am

Please forgive my ignorance, but what holds the oil cooler sandwich plate in position? I've read about the o ring behind it, but no mention of ...   02-02-2017 03:28 am

today continued my carb experiments.. I began with a 45 jet in the cold start, way too lean took that out and put the 95 back in, ...   01-31-2017 11:31 pm

took it off the lift and drove it around today. It actually worked. Now wheel alignment ...   01-30-2017 11:54 pm

for those following, I hooked up my AEM air fuel gauge yesterday...still didn't drive the car, but got some idle/cold start/ no load info. FIrst cold ...   01-30-2017 03:24 pm

OK....door on, dash wood veneered and varnished, hazard switch replaced and rewired, carpet in, seats in, radio wiring fixed and connected https://www.snapfish.com/library/share?w=snapfish_us&c=snapfish&l=en_US#NMCz3hbl_p2ILrHjKYQxIQ/AUS/27941460266070/SNAPFISH ...   01-30-2017 04:53 am

while I'm aware of the accelerator pump jet, is there an adjustment for the accelerator pump stroke? Any way to alter its performance through ...   01-19-2017 04:11 pm

with any luck I'll actually get the door back on today ...   01-19-2017 04:07 pm

checked, DHLA 45, no letter ...   01-12-2017 09:20 pm

I believe my carbs are plain "45", but I'll check to be sure. RE: the idle air corrector-do the leaner numbers have larger or more emulsion ...   01-09-2017 03:16 pm

https://www.youtube.com/watch?v=KGVcJrEJW7E ...   12-26-2016 03:32 am

I'm just curious if anyone has deleted the oil cooler.  Is it really necessary?  Does this engine generate that much internal friction that it overheats ...   12-25-2016 05:47 pm

Nigel, that's good news..hope it's a permanent fix ...   12-21-2016 04:40 am

that's a very well thought out modification.. I like it..do you have Zenith or Dellorto manifold...I assume Euro spec mean Dellorto but I'm usually wrong ...   12-21-2016 04:40 am

I wound up using the hose adapter from these guys. https://www.hollisterroad.com/proddetail.php?prod=WTRS123004 They also offer temperature switches. I got 200 on 185 off....works awesome ...   12-16-2016 11:11 pm