Can someone confirm what the correct Krikit measurements are? In another post someone said around 50-52 which is what I used. ...   09-01-2015 06:01 pm

After sitting for a couple months, I started my car up and drove it for a while. It ran fine, but once it was hot ...   08-28-2015 08:15 pm

The adjustment bolt (copper?) going into the brake booster rod was bent and stripped and while trying to remove it the head broke off. Is ...   12-08-2013 12:58 am

Thanks for putting this up. I've seen many references to it on various posts and was disappointed to see they were down. ...   11-23-2013 12:00 am

To the brake booster. I read on a BMW forum that white smoke can be produced when the master cylinder leaks into the booster and ...   11-20-2013 07:39 pm

About 55k,original engine. No smoke though after taking off vacuum hose. Really odd. ...   11-20-2013 05:38 pm

Thanks for the reply, but I found it was something a little more odd last night. The master cylinder was leaking brake fluid and it ...   11-20-2013 02:45 pm

I'm getting pretty bad smoking once warmed up. It's quite a bit and usually around idle RPM's, although it also does higher up also. It's ...   11-20-2013 12:47 am

In other posts, some say to use butyl tape, others say urethane sealant. There's also this 3M product http://www.amazon.com/3M-08609-Window-Weld-Urethane-Cartridge/dp/B000FW61EW/ref=sr_1_1?ie=UTF8&qid=1383780490&sr=8-1&keywords=windo-weld as well as the tape version, http://www.amazon.com/3M-08612-Window-Weld-Ribbon-Sealer/dp/B000CQ4AOO/ref=sr_1_6?ie=UTF8&qid=1383780602&sr=8-6&keywords=windo-weld which ...   11-06-2013 10:31 pm

Here's some pictures. As you can see there's a little staining where the hardware was attached. It could use a polish. Let me know if ...   11-03-2013 01:38 am

I have one in storage. I'll get it out and post pictures later today. Can't remember what condition it's in though. ...   11-01-2013 04:41 pm

Called him today and he does the JH boosters as well as TR6 ones. Its $120 to rebuild plus $30 for powdercoating. Pulled it from ...   10-10-2013 04:37 am

My brake booster has a significant vacuum leak and needs to be rebuilt. What is the best way to go about this? Are there kits ...   10-08-2013 08:15 pm

I have not checked the valve clearances. Well, it may be a 2.2 stroker after all. My dad said the ad from 3 years ago ...   09-27-2013 01:43 am

Could you please do that? The diagrams would be very helpful for figuring out the confusing bits of the wiring I'm doing right now. ...   09-26-2013 07:57 pm

We drove it around the block three years ago but that's it. The rest of the car was rebuilt but the motor was left untouched ...   09-25-2013 07:49 pm

Any advice as to which/where to get a wide band a/f gauge? ...   09-24-2013 07:59 pm

Is there any way to tell if anything is modified without taking the heads off? ...   09-24-2013 05:37 pm

I know the cams are stock and I think the pistons are also stock. Haven't torn apart the engine though so I don't know for ...   09-24-2013 02:36 pm

Thanks for your quick reply. The timing is set at 12 degrees and I think the ignition is correct. It has pertronix so there shouldn't ...   09-24-2013 05:58 am

The engine is in the car and running, but it doesn't like RPM's below 1200 or so, when it starts rocking and mis-firing. One of ...   09-24-2013 05:02 am

This one? http://ten680.wordpress.com/2011/06/26/new-rear-bumpers/ ...   09-10-2011 06:46 pm

This may sound stupid, but how would you know what cams and which Dellorto's(40 or 45's) are on your car? I'm asking because I bought ...   05-31-2011 08:34 pm

Sorry for the revival of a really old thread, but does anyone have an archive of John's website? It looks very helpful. Thanks. ...   04-06-2011 10:57 pm

Does anyone know how to get the rubber cones that stop the suspension from bottoming out on the rear removed? Thanks in advance. ...   03-02-2011 01:16 am

Thanks guys. ...   01-05-2011 04:30 am

On my 5 speed transmission, when you put it into reverse, 2nd, or 4th, the gearshift pushes the whole center console forwards. Is there a ...   01-04-2011 11:13 pm

The wiring that goes to the back of the fuse box. ...   12-30-2010 12:50 am

I am pulling the wiring harness, and got the fuse box out after much mutilation of the bracket. Is there any way to get the ...   12-30-2010 12:47 am