Has anybody replace their speedometer gear? How do you remove it from the main shaft? I don't want to damage anything further than it already ...   04-28-2016 05:31 pm

I switched the 4 way flashers on and off and that stopped it. In the past I have noticed the right blinkers are slow to ...   03-01-2016 08:15 pm

My Jensen has been sitting in my garage for weeks without being driven. I came home last night and opened the garage door to find ...   02-29-2016 06:17 pm

When starting my Jensen after it sits for a day or so I have to pull the choke to start it up. I have thought ...   11-03-2015 12:59 am

I have some. PM me and I will send pictures. ...   09-28-2013 07:31 pm

I have one. I Sent you a pm. ...   02-03-2013 10:56 pm

I just pulled off the resistor wire off the + side of the coil and got 11.60v ...   10-11-2012 11:05 pm

And here i have just been flipping the toggle switch ...   09-16-2012 05:06 pm

The oil was new. The po noted that the engine had 5000mi on a rebuild for what that is worth. The oil has a heavy ...   09-15-2012 09:12 pm

The engine had been out for 9 years before i bought the car and put it in. I have only run the engine maybe 5 ...   09-15-2012 02:23 am

It has been sitting in a jar for several days and doesn't appear to separate. My coolant level was low. I filled the radiator and ...   09-14-2012 07:16 pm

I have been putting to gether my JH and tuning the motor. After reading some posts on oil I realized I needed to change mine. ...   09-10-2012 05:58 pm

The blinker on the bumper has a green and a red wire. The car side has three: red, black and green with red stripe.http://i741.photobucket.com/albums/xx57/chiromaster/newtop019.jpg http://i741.photobucket.com/albums/xx57/chiromaster/newtop018.jpg   ...   06-09-2012 04:27 am

I went to hook up the turn signals on my 73 and noticed the plug on the car has 3 wires and the blinker has ...   06-09-2012 12:59 am

Club Store http://www.jhps.com/mm5/merchant.mvc?Screen=PROD&Store_Code=Warehouse&Product_Code=90111&Category_Code=Body ...   02-14-2012 09:07 pm

What has been the best way to attach the boot lid finisher? Specifically the middle three holes.  I have the stud plates for the other ...   02-13-2012 09:15 pm

After putting the carpet kit in my JH it was time for dash re assembly. The dash board has been in the car by its ...   01-11-2012 10:39 pm

Nice ride! ...   07-21-2011 04:02 am

What type of wheel or lug pattern are you looking to adapt to? Have you considered wheel size, offsets and tire size? ...   07-19-2011 12:51 am

If you want serious power just drop in a V6...Yeah, I'm just kidding! ...   05-26-2011 12:58 am

IMPRESSIVE! ...   05-02-2011 02:29 am

Just back from the driveway… Cam belt done with new tensioner. Fuse box checked Cooling system flushed and filled. Took out multimeter to check some voltages. The wire ...   04-25-2011 08:54 pm

Not even close. Now the story of this car is clearer. The people who sold it to my friend messed around with the carbs for ...   04-25-2011 07:05 pm

I did check the floats for leaks. They are fine. When I did the rebuild, I did one carb at a time being careful to ...   04-25-2011 03:48 pm

When I got my JH it had Weber 45's on it. It had been sitting for many years. When I tried to start it gas ...   04-25-2011 12:43 am

Found these tires... http://www.performanceplustire.com/products/tires/searchType/searchBySize/tireSize/205_SLASH_60-13 Maybe one of these would work well for us. I apparently didn't get the Sumitomo tires I ordered either.   ...   04-24-2011 12:18 am

http://www.discount-tires-2go.com/Store_Detail.cfm?ID=183240&InfoID=4853&ShowLarge=True   Just bought a set of Sumitomo HTR 200 205/60/13's found a set of TOYO R888 205 60 13 on ebay as well. Use 205 60 13 ...   04-18-2011 09:37 pm

http://home.comcast.net/~jrkengr2/html/pictures.html ...   04-07-2011 03:07 pm

MMMMMM Y pipe. That looks like the one. ...   12-04-2010 01:29 am

Bought new exhaust system from Delta but they have no Y pipes (nor do I). Has anybody else had this problem? Can this be easily ...   12-03-2010 10:17 pm

I bought a Jensen that already has an allison xr700 installed and have a MSD 6A to add to it. Called MSD to get wiring schematic ...   11-10-2010 08:45 pm

I can be in for 11/6. Nels ...   10-18-2010 02:23 pm

Thank you all for the input on bumper restoration. I will start with the cleaning methods first. If they don't work I will get busy ...   08-16-2010 03:39 pm

They are rubber bumpers. The rubber is hard and looks cracked from the AZ sun. It looks as they may have been coated with something ...   08-14-2010 02:21 am

My bumpers need help. They are weathered looking. What steps should I take to restore them? What products are good to re finish with?  Thank You Nels ...   08-14-2010 01:53 am

I can see this is an old post but I have the same problem. Welding and cutting is no problem for me. Any other insight, ...   03-26-2010 09:26 pm

I am in the same rusty boat. Any updates on the process and progress? Any pictures ...   03-25-2010 03:26 pm