I looked at this tonight again and needle nose are just not going to cut it. I am thinking of losening the pedal box to ...   05-07-2008 01:21 am

Guys the funnest part about this is my arms will not fold up enough to get under there with my head. I am 6'6" tall ...   05-06-2008 10:36 pm

I would prefer not to have to alter the structure of the car to achieve this replacement. Anyone else have any suggestions? ...   05-06-2008 01:23 pm

Alright, guys I got it all put back together and started the engine up yesterday. Reset the timing and tried to tune the carbs. I ...   05-04-2008 07:05 pm

Does any one know the what other spark plug wire set interchanges with the JH? I have tried the universal sets and am not impressed. ...   04-29-2008 01:37 am

Thanks for the responses guys. I was able to take the carb to a quality machine shop and have the threads straightened. They had to ...   04-18-2008 01:54 pm

Alright guys. I went ahead an cleaned them in the bucket-o-carb cleaner and not the ultrasonic route. I have assembled one and noticed there are ...   04-09-2008 01:41 am

I am going to try my hand at rebuilding my 45mm Dellortos and am sure to need some help from you experienced guys. The first ...   03-27-2008 03:27 am

Thanks for your replies. I looked into it further tonight and used carb cleaner as suggested and verified the vaccum advance has been disabled. Hooked ...   08-02-2007 01:17 am

I started my JH up saturday after 5 years of storage and I can not seem to get the idle down to a resonable level. ...   07-31-2007 02:12 pm

What would you think of using a engine flush additive on one of the last changes of oil prior to the use of 20-50? ...   07-30-2007 01:30 pm

I started up my JH after 5 years tonight. I had stored it with mavel in the cylindertops to preserve the rings. However, tonight when ...   07-29-2007 03:19 am

My castings are so rough I am certain it would take a good long while to polish mine. I was hoping that would be an ...   06-30-2007 08:56 pm

I was thinking of either using the color polished aluminum of smoked chrome which are both very similar. I also like the wrinkle coat, but ...   06-30-2007 06:02 pm

I have removed my cam covers and bead blasted them. I want to powder coat them and am not certain if I need to use ...   06-29-2007 06:13 pm

YGM ...   06-22-2007 02:49 pm

Sylva, Great of you to offer. I have sent you a PM with my address so you can verify shipping cost. I really appreciate this! Thanks, Brad ...   06-21-2007 08:16 pm

Does anyone know where I might obtain a set of new or slightly used timing belt gears for the cams. Mine are worn a bit ...   06-18-2007 05:58 pm

Jeorge currently has the aluminum tank listed on ebay for $299.95 buy it now price. Anyone looking for a tank or thinking of rebuilding your ...   11-18-2006 08:13 pm

I am really confused now about ths anti-syphon check valve. The reasons I am confused is... Delta mention this line as a return line and an ...   11-02-2006 03:47 am

Two additional questions 1. Two choices of fuel pressure regulators are 1-4 psi and 4-9 psi. My jensen currently has strombergs on it, but just until ...   11-01-2006 02:34 pm

Thanks guys for the feedback. Just to make sure I have this correct I will restate what think we have concluded. The small steel vent ...   10-30-2006 09:23 pm

Hey guys, I bought one of the new almunimum tanks from George a few month back and am now getting ready to install it. There is ...   10-28-2006 06:46 pm

I would be interested. ...   03-07-2006 01:38 pm

I too am interested in what the others thoughts are on this. As for my own I will fill my tank with water soon to ...   10-20-2005 06:12 pm

Got mine yesterday! I have not considered sealing or painting my new tank. Why do you think aluminum can rust? SS can if in direct ...   10-20-2005 03:00 pm

HI BRAD, TOMORROW WE ARE SHIPPING THE FIRST 4 FUEL TANKS ON THE LIST... NEXT WEEK WE'LL SHIP THE REST... REGARDS, JORGE CERVERA Jorge, Just ...   10-13-2005 02:13 pm

I have been asked to update the list of members in this thread concerning payments recieved. 1.- BRAD KESLER - jensen4u 2.- LEON McGEE (Associate of Dan's) - Dan ...   09-29-2005 05:47 pm

All, I would like to thank all for your fast responses and payments. It appeared that there was some sort of mix up and that all ...   09-27-2005 01:32 pm

All, Jorge has sent me an email stating he has only recieved payment from the following. 1.- BRAD KESLER – jensen4u 2.- LEON McGEE - ? 3.- GARY MARTIN ...   09-25-2005 04:21 pm

Guys, I have sent either a private maessage or email to each of the committed members. Please confirm once you have made payment. If for any ...   09-15-2005 07:23 pm

Guys, It is done! I have placed the order for 8 aluminum JH fuel tanks. Jorge was kind enough to honor the price for 10 as ...   09-15-2005 07:07 pm

Hey Guys, Tonight is your last chance to get in on this special priced aluminum tank. Please let me know if you are in. The current ...   09-15-2005 01:19 am

All, Very surprised the list has not changed over the weekend! Never the less I will attempt to place this order with Jorge on Thurs 09/15/05. Therefore, I ...   09-12-2005 04:03 pm

The current committed list is: Gary Martin, Dan Collier, Jim Sohl, Pchung, Joel, Harkes, themagicalswitch, and myself We have 8 only 2 more to go..... ...   09-09-2005 07:10 pm

Anyone, It has been a few days and I have no feedback as to where we stand on a production run of wheels for the JH. ...   09-09-2005 01:49 pm

The current committed list is: Dan Collier, Jim Sohl, Pchung, Joel, Harkes, themagicalswitch, and myself We have 7 only 3 more to go.....   ...   09-09-2005 01:45 pm

The current committed list is: Jim Sohl, Pchung, Joel, Harkes, themagicalswitch, and myself We have 6 only 4 more to go..... ...   09-09-2005 02:10 am

All, So far I have the following people commited for the aluminum tank + shipping for $500 Pchung, Joel, Harkes, themagicalswitch, and myself We have 5 to ...   09-08-2005 02:36 pm

Some more information for those whom are interested. HELLO BRAD, I ONLY MADE THE PROTOTYPE IN MILD STEEL, HERE IS A PHOTO... THE TANKS WILL BE ...   09-07-2005 08:35 pm