Frank, Thanks for all the clarifications. Now if i can only find the holes, i just need to find a way to thread the vacuum hoses ...   03-31-2014 07:30 pm

Frank I noticed that all 1/4 in. vacuum hoses going to/from the heater system are missing. I understand the regulating control valve is mounted above the ...   03-30-2014 07:15 pm

To all the Dellorto Experts, i have DHLA 40N installed on my tangerine orange JH, the carbs have been cleaned and checked with new seals ...   09-16-2013 05:34 pm

Thanks for the information, would you have any suggestion for someone familiar with doing such rebuild in NorCal? FranciG ...   08-25-2013 06:52 pm

To all you experts, after about 3 years and vast amount of  money my "Phoenix" is coming close to resurection. However my mechanic (a Lotus ...   08-04-2013 03:50 am

Help, I am looking for the Nilos part number usually stamped on the seal outer surface. Thanks FG ...   03-15-2013 04:39 pm

Help, I am looking for the Nilos part number usually stamped on the seal outer surface. Thanks FG ...   03-15-2013 04:39 pm

Are these the bushings used to connect the cross-member to the chassis? Pictures would be great. I am in San Rafael. FG ...   02-27-2013 11:30 pm

Would anyone know of a serviceable rear end for a 4 speed transmission for sale? Please call me at 415-279-0609 ...   11-28-2012 12:56 am

If you are using a stock JH oil  cooler note the hose connections are all 5/8"  BSP (british standard pipe). good luck ...   11-04-2011 11:56 pm

Thanks to all for the help. I guess i will stick with the stock size, if i can only find some. ...   05-16-2011 10:09 pm

Does anyone have a suggestion for an optimum size/length of the Velocity stacks to be used for the twin DHLA 40 carburetor on a stock ...   05-15-2011 11:12 pm

Speedy Mitch, Nice job on the mirror, i only wish i still had mine...  We must be neighbours i am in SR. FG ...   02-19-2011 01:07 am

I simply took the trunk lid off ...   11-15-2010 11:00 pm

Philharmonic, I ran into the same problem with the factory paint code and had to have the paint scanned by Finish Master in San Rafafel CA ...   11-15-2010 10:36 pm

What sort of proportionning valve are you using? ...   02-03-2010 09:53 pm

To all, Thanks for all the info. I still have some questions for those who have gone down this road before. I decided on the Volvo ...   02-01-2010 03:49 am

Greg Thanks for the info. Would you have any idea as to where i may find longer wheel studs that would fit in the stock JH ...   01-14-2010 03:18 am

Greg Thanks for the information. I dont know if i want to re-engineer the Volvo Calipers, but i  will look at the 70's Jaguar XJ12 calipers, Porsche ...   01-13-2010 05:10 am

Greg, A few questions for you: 1. Do the the Volvo 4 piston calipers allow for vented rotors and if so what is the max thickness? 2. Where ...   01-11-2010 05:28 am

Greg, Great pictures. After doing the upgrade did you notice any problem with flexing of the caliper spindle mount, they seem so small compared to the ...   10-21-2009 05:36 pm

Has anyone ever installed the Volvo twin piston calipers and master cylinder from a, Volvo 240 series, is the caliper bolt pattern the same, will the ...   09-27-2009 06:55 pm

I have a few questions for any or our esteemed experts concerning the mounting and initial setup of Dellorto DHLA 40. 1. Where do the rubber ...   09-14-2009 05:24 am

Colin, Thanks for the info. I have an ICI paint code i found on the message board (ICI M0788483) but could not find anyone using ICI ...   05-15-2009 03:41 pm

For anytone considering matching the Tangerine Orange of the factory color. I had a color scan made by a automotive paint shop, the closest match ...   05-15-2009 12:21 am

Does anyone know what the factory paint codes are or their equivalents from Dupont, PPG, or Sherwin Williams? No one has been able to cross over ...   05-14-2009 04:16 pm

Thanks for the information. Francis G ...   04-12-2009 04:23 am

I am the new owner of a 1974 model, however the fuel tank was out of the car without a fuel tank sending unit. I ...   04-11-2009 10:25 pm