I have a set of 45 dellortos that need repair. More than a simple rebuild. A couple of adjustment screws need to be ...   05-09-2018 03:51 pm

I am looking for seats that fit my JH. Leather would be nice. Any ideas on what fits from another car? ...   04-23-2014 01:39 pm

thanks for the input.  Additional information;  the clutch was recently replaced.  This should mean some of the issues you mention would not be a factor, ...   07-29-2013 10:12 pm

I am having difficulty shifting into fist and second when stopped and sometimes when rolling slowly.  If I shift into 3rd and release the clutch ...   07-29-2013 06:28 pm

the u joint cost $64 US. 40% of that was shipping. ...   07-24-2013 01:55 pm

My project is complete.  I procured a new lower u joint from Martin Robey.  Just getting the part was the hardest task, as I could ...   07-23-2013 06:15 pm

thanks.  good to know. ...   06-26-2013 04:18 pm

I found the Robey website and the part, and tried to connect with them by email without success so far.  Is it necessary to order ...   06-26-2013 02:52 pm

thanks for the offer.  I am trying to connect with martin robey in England.  considering what a pain it is to take this out and ...   06-26-2013 02:50 pm

Delta does not have a source for them.  I would welcome any suggestions.  I see the club store has the shaft, but looks like it ...   06-25-2013 03:07 pm

Is there a source for a replacement for the lower steering knuckle? ...   06-24-2013 01:16 pm

thanks   ...   06-20-2013 01:57 pm

Can someone provide a procedure for installing this?  It appears that it is necessary to remove the shaft between the firewall and the rack, pull ...   06-19-2013 10:01 pm

I do not find much in the shop manual on replacing the clutch parts.  Any clues?   I did find the most excellent article posted in the ...   06-27-2012 02:30 pm

I occurred to me that I should check for free play in the front wheel bearings.  Any advice on how to assess how tight they ...   06-18-2012 08:14 pm

what has been your experience with removing the old ones? ...   06-13-2012 02:03 pm

I have oil leaking at the exhaust cam front seal.  Is it necessary to remove the cam from the carrier to replace this or can ...   06-12-2012 06:54 pm

thanks for the input.  I will check for interference with the knuckles.  I have experienced that before I put in new engine mounts.  Also the ...   06-12-2012 02:50 pm

I am noticing some issues with the steering.  the wheel feels good and tight but it seems like the car wanders a bit.  Also,  I ...   06-11-2012 06:43 pm

I just went through the same drill.  The plug in my carb has 4 tabs (stromberg manual indicates there should be 4).  I could not ...   06-07-2012 06:02 pm

I just had the same snap ring experience on my lockheed cylinders.  they both broke.  I picked up replacements at the local farm and fleet ...   05-07-2012 03:17 pm

I need to replace the wheel cylinders and shoes.  Any advice on the process? ...   04-13-2012 09:39 pm

I believe my clutch needs an adjustment.  I found an article on line describing how to do it but I am looking for additional advice.  ...   11-10-2011 08:44 pm

I recently replaced the tensioner bearings.  I had them pressed in by a local shop.  A couple of weeks later, I discovered that the pulley ...   10-12-2011 10:19 pm

Mine are 45's.  Thanks for checking in. ...   08-29-2011 02:06 pm

I have a Dellorto carb that need some replacement parts.  The body has two adjustment screws that are frozen and there is a crack in ...   08-25-2011 06:10 pm

I have installed the new intake manifold gasket and so far it seems to have stopped all coolant leaks.  This was a great relief after ...   08-22-2011 09:08 pm

thanks, Brett.  Any idea what accounts for the leak?  It does seem to come right from the rear most of those two missing studs.  Do ...   08-09-2011 02:38 pm

I think I have coolant leaking out from between the intake manifold and the head.  I noticed that there are no studs in the two ...   08-08-2011 07:43 pm

thanks for the feedback.  what product did you use? ...   06-23-2011 02:33 pm

I suspect I may have coolant seeping out through the head gasket.  No water in the oil; just coolant on the side of the engine.  ...   06-17-2011 01:53 pm

what does that look like?  What is involved? ...   05-18-2011 03:46 pm

The valve adjustment instructions in the newsletter describes an O-ring around the oil feed tube at the front of the cam tower.  It also describes ...   05-18-2011 02:43 pm

I guess the only reason not to do it would be the hassle.  Anyway, I tore it all apart last night; both sides.  The next ...   05-17-2011 02:39 pm

I checked my valve clearances.  The exhausts are all quite low and I am going to adjust them.  Three of the intakes are at .004.  ...   05-16-2011 06:45 pm

John, I think you showed me your setup to catch oil from the breather tube a couple of years ago.  Can you send me a ...   05-03-2011 06:59 pm

what is the appropriate way to capture the oil that comes out of the crankcase breather?  Mine just dumps on the lower suspension members and ...   05-03-2011 06:41 pm

I purchased new gears from Delta and got them in the mail yesterday.  I spent some time looking over the car.  I may have gone ...   05-03-2011 02:40 pm

I have decided to replace the timing gears  (cams and distributor).  removing the cam gears looks easy.  The distributor gear appears to be attached with ...   04-28-2011 06:28 pm

I just got the rebuild kits in the mail from Delta.  I did find a vacuum leak.  Fixiing that helped but it still feels like ...   09-02-2009 01:52 pm