That worked. Thank you. ...   10-13-2015 08:42 pm

Lately I am getting a "502 Bad Gateway" error message when I click on many of the messages in the "recent" topics. ...   10-12-2015 07:31 pm

Would anyone have a suggestion on where I could find a workshop manual for the 1974 Lotus 907 engine? I would love to read all ...   10-06-2015 08:02 pm

I'm looking at the need to get into the valves. I'm suspecting a burnt valve. Question, do I need to remove the cam towers from ...   10-06-2015 07:45 pm

I would be interested in this topic. A photo or two of location and detail would help. Thanks,   ...   03-04-2014 05:44 pm

While thinking about this vacuum test of the booster, I'm wodering... I plan to connect the vacuum pump to the hose that will then connect to ...   11-26-2013 05:49 pm

If I were to use my Mity Vac to check the booster, how much vacuum would it be expected to hold, and for how long. ...   11-22-2013 08:06 pm

Can anyone tell me the purpose of the hose that appears to be connected to the rear axle housing and runs up into the body, ...   08-30-2012 05:31 pm

I'm thinking if you have a leak from the hole where the switch mounts then you must have a leak from one or both sides ...   07-16-2012 12:39 pm

I sure would like to be going, but I believe that my schedule will not allow. I hope that there is a great turnout for ...   05-24-2012 05:47 pm

Excuse me but, what is meant by “nip”? And what is its' function? ...   12-05-2011 05:18 pm

Is there a way of setting what is considered "Recent" when viewing the Recent messages? How far back does it go? and Can this be ...   07-19-2011 06:00 pm

I replaced both of the O-Rings with 5/8" ID x 13/16 OD standard O-Rings from a local NAPA store. The material was listed as Nitrile. I ...   05-20-2011 06:04 pm

So there is no turning involved other than trying to loosen the fit of the o-ring? There are no threads? ...   05-16-2011 08:54 pm

I noticed gas dripping from what looke like a plug in the bottom of the front carburetor bowl. At first look it appeared that the ...   05-16-2011 05:49 pm

The possible extra fuse was for protection from a potential short circuit in the control wires coming from the headlight switch. If sufficient care is taken ...   01-31-2011 07:25 pm

For the replay circuit, I refered to the following with good success. http://home.comcast.net/~jrkengr2/html/headlight_relays.html A very informative site. I bought some relays from JC Whitney. My installation looks very similar. Be ...   01-31-2011 05:59 pm

corrected link http://wheels.blogs.nytimes.com/2009/07/13/jensen-lovers-gather-in-pennsylvania/?pagemode=print ...   07-15-2009 05:04 pm

YELODOG, Thanks for the information (and the part numbers). I wasn't sure of the thread sizes. I think I'll order some soon. Jay ...   02-09-2009 01:07 pm

Pete, Could you recommend a source for the Speed Bleeders? I think that I would like to get some the my JH. Thanks, Jay ...   02-06-2009 03:18 pm

I'm just now in the process of building new door panels myself. I will heed your warning. I plan to test fit the bare board ...   08-28-2008 12:24 pm

I got a pair of the outer wipes from McGregor a while back. I am now contemplating their installation. Can anyone step me through the process. ...   08-04-2008 03:56 pm

Andy, Something like that is what I thought may be worth a try. I was hoping someone may have already tried this. Thanks for the tip. With ...   06-04-2008 04:23 pm

My brake warning light is now on, after I replaced my master cylinder. I bled both the front and rear before I ever had the ...   06-02-2008 03:50 pm

I was thinking about getting one of those vacuum pumps (MityVac) to bleed my brakes. Has anyone used one of those hand held vacuum pumps to ...   04-02-2008 05:08 pm

Accusump or MasterLube Still trying to decide which to go with. The Accusump with it's piston between the air and the oil, or the MasterLube with ...   04-02-2008 04:54 pm

Harkes wrote: Isn't the TR6 Girling Brake Booster exactly the same as well? I always believed this. Can anyone confirm this? These are readily available ...   04-01-2008 11:47 am

I'm loosing my brakes fast. It's time for that brake job, master cylinder, pads, shoes... I thought that I should check, clean and/or rebuild the ...   03-31-2008 09:48 pm

I have been considering the installation of an Accusump or MasterLube as described in the March 2002 issue of the JHPS Magazine. I like the ...   03-07-2008 05:46 pm

My 74 JH has what appears to be a silver painted ring on the outer trim of the vents. The paint is about 30% worn ...   08-28-2007 04:03 am

I am truly saddened and offer my heartfelt condolences to Mark's family and friends. All of us who read and post to this message board ...   07-25-2007 05:05 pm

I found a write-up of the cooling system and thermostat for the 907. This information also seems to make a lot of sense to me. http://www.gglotus.org/ggtech/907overheat/907overheating.htm ...   05-17-2007 09:29 pm

Thank you Jim. I thought there may be more to the story. By all means I want as much cooling effect as I can get. I ...   05-17-2007 08:32 pm

Last night I set out to change out the old thermostat with a new fail-safe new one. Before I install the new one I wanted to ...   05-17-2007 07:06 pm

While on the topic of the oil pump, I have some general questions. First: If I suspected that my oil pressure was not as high as recommend, ...   02-06-2007 06:31 pm

Try this link. http://www.austinev.org/evalbum/279.html I seem to remember some other web page(s) that had information and photos of this car. ...   11-16-2006 06:24 pm

I have seen (on web somewhere) a JH that was converted to electric drive. I'll try to find it again. As I recall, the one ...   11-16-2006 05:12 pm

Mark, I believe I found your writr-up on the old board. Is the Roadster Factory part number(s) that you quoted, GI64068822 - "T56 Master Cylinder Assy, ...   11-14-2006 08:02 pm

My JH brakes seem to work pretty well in general. If you apply them at a somewhat normal speed (that is to say, the speed ...   11-10-2006 05:31 pm

There is a Robbins top listed in the Warehouse section under Body. Code number 2440CG ...   10-03-2006 03:34 pm