I did both of my cars with 3M Black super weatherstrip and gasket adhesive. Worked great. Left the glass up to provide pressure ...   03-13-2019 12:40 am

Matt I purchased one of the clutch lever boot covers from your dad when I restored my first car. I would like to purchase another ...   02-21-2019 10:28 pm

Tim Thanks for the reply and Picture. I looked and I actually found one in my parts. Did not know what is was before. spoke ...   10-07-2018 09:51 pm

The more research I do on the tank pluming the more confused I get. Does the restrictor go in the return line from the ...   10-05-2018 07:07 pm

Thanks for the reply's. Now to figure out how to make an in line restrictor. I assume they are not available. Any ideas? ...   10-04-2018 07:46 pm

Help. I screwed up on both my cars when I installed the fuel tanks. I noticed this when I happened to look at a fuel ...   10-03-2018 12:00 am

Got the carbs off. I had had them "re-manufactured" in town at a carb shop. Only had put 35 miles on the car ...   05-21-2018 11:00 pm

Plan to take the carbs off today and check floats. ...   05-21-2018 05:10 pm

Thanks for the infromation. I have 2.0 PSI at the carburetor. Which I see is at the bottom end of the range. The ...   05-21-2018 12:00 am

Looking for fuel pressure specs at the fuel pump and at the Carburetor. The car is surging and I think I may have a weak ...   05-20-2018 10:09 pm

Thanks for the information. If I had seen Bruce's post before I ordered the rebuilt one I may have plugged mine. Will save ...   08-30-2017 10:14 pm

Thanks for the help Tim. Will follow your instructions when I bleed the brakes. Just got the rebuilt PDWA but I have to first ...   08-30-2017 03:55 am

Dealing with a North American Safety device, the Pressure Differential Warning Actuator. Just finished the car and the brake fail light stays on ...   08-29-2017 11:10 pm

Just got my catalogs from Metro and Steele Rubber Products. I noticed the Steele has locking strips with chrome face on page 5. ...   06-12-2017 11:06 pm

Thanks for the leads. I have two tops. One is a factory and one is after market. The factory top has a black ...   06-09-2017 12:24 am

Thanks Brett for the link. I am also checking Metro and Steele rubber products to see if they a profile close. ...   06-08-2017 06:57 pm

Thanks for the recommendations. I have a spare wheel I am going to try it on before the top. I also need to replace ...   06-07-2017 05:44 pm

Has anyone painted a hard top. I have two of them. One has some minor scratches. I want to repair these and then ...   06-06-2017 08:51 pm

Thanks for the reply. I have the lock mechanism off. Is there any way to get the cylinder out to take to a ...   07-14-2016 05:22 pm

How do you remove the ignition switch? ...   07-14-2016 06:06 am

Just got back from a trip and saw your reply. I think I just decided on the color. Thanks for the picture. ...   02-07-2015 09:52 pm

Thanks guys for the information. It doesn't have to be the exact original red. I like the cardinal red and will see if ...   01-28-2015 08:35 pm

My 74 is blocked, primed and ready to go to the paint shop. Would like to find a red close to original. No ...   01-27-2015 08:16 pm

Thanks for the reply. I was afraid that was the case. I have a spare rack that does not appear to have any play ...   12-21-2013 12:26 am

Is there any way to adjust the play out in the steering rack? I have checked everything else and the steering play is in ...   12-20-2013 09:42 pm

Jim, thanks for the help.  I am going to take the shim route. ...   12-04-2011 12:18 am

This is the first time I have posted to the message board. Between reading the message, board, the Preservation Society publication and the other information ...   11-29-2011 12:27 am