| ||||
| ||||
| Moderated by: Greg Fletcher |
|
||||||||||||||
| Lucas 25d distibutor body | Rate Topic |
| Author | Post |
|---|
| Posted: 11-09-2020 11:59 am |
|
1st Post |
|
rschlemm Member
|
the area on the distributor (aluminum) where the steel ring secures the distributor to the oil pump has fractured and can no longer be secured with the retaining ring. I had previously used JB Weld to hold these pieces together but it broke over the weekend. I knew it was on borrowed time when i put it together, but wanted to enjoy the car over the summer. Can the Moss 25D distributor for the MG be used, transplanting the guts from my distributor into the new body? Or can a later distributor body be used?
|
||||||||||||||
| |||||||||||||||
| Posted: 11-09-2020 02:05 pm |
|
2nd Post |
|
redracer Member
|
basically, yes(the 5 digit # stamped on the front may be different, but you will need to transfer the guts; might as well change the seal while you're in there) btw, I have MANY good used ones and I'm sure others do as well
|
|||||||||||||
| ||||||||||||||
| Posted: 11-10-2020 12:30 pm |
|
3rd Post |
|
rschlemm Member
|
if anyone has a good 25D distributor body for sale send me a PM.
|
||||||||||||||
| |||||||||||||||
| Posted: 11-10-2020 02:36 pm |
|
4th Post |
|
Brett Gibson JH5 20497 Member
|
If you are going to have the dizzy apart don't forget to add the inner oil seal update, if you need details go to Jensen-Healey on Facebook, in the files section. Brett.
|
|||||||||||||
| ||||||||||||||
| Posted: 11-10-2020 03:23 pm |
|
5th Post |
|
redracer Member
|
As I previously as stated, I have quite a few. I don't know if you want to rebuild it yourself, or have me do It (I have probably rebuilt well over 100). Try me at my regular email; RedRacerbm@gamil.com as that will be much faster to respond
|
||||||||||||||
| |||||||||||||||
| Posted: 11-10-2020 10:18 pm |
|
6th Post |
|
DonBurns Member
|
On my first JH (14313) I was forever having the 25D pop out when I loosened to adjust the timing. It may have been because the skirt was already cracked, but anyway it finally broke completely. I took to a friendly machine shop and they cut away the aluminum skirt and replaced with a press fit steel sleeve. I asked them to add a very slight raised "catch" at the end. Just enough that the pinch clamp would catch and I could loosen the clamp and turn the distributor without having to worry about it popping out on me, which as you know makes for a bigger project. I could still remove the distributor by putting a flat screwdriver at the end of the clamp and twisting. Has anyone else done this?
|
|||||||||||||
| ||||||||||||||
| Posted: 11-10-2020 11:42 pm |
|
7th Post |
|
discogodfather Member 
|
I didn't add a lip but I do add a small turned steel ring into the gap between the edge and the main body so that it has something to clamp against. Seems to be working well. I might try that idea of just machining it all away and adding a larger steel ring, that would be probably the best thing. It's just an awful design in general, thought many times of doing something custom that had a tab that attached to the oil pump housing and another tab on the distributor and just bolt it together, similar to every other car company did with a brain.
|
||||||||||||||
| |||||||||||||||
| Posted: 03-10-2021 08:36 pm |
|
8th Post |
|
Distributorguy Member
|
That crack can be repaired permanently. Send it in to JHPS for a rebuild/recurve along with your bent clamp and it'll come back fully rebuilt and repaired, ready for another lifetime of service. Its an easy fix.
|
|||||||||||||
| ||||||||||||||
| Current time is 10:48 am | |
| > Jensen Healey & Jensen GT Tech > Ignition > Lucas 25d distibutor body | Top |
