| ||||
| ||||
| Moderated by: Greg Fletcher |
|
||||||||||||||
| Uni-Syn Balancer | Rating: 
|
| Author | Post |
|---|
| Posted: 08-01-2007 01:50 am |
|
1st Post |
|
Steve Jarvis Member
|
I bought a Uni-Syn balancer to synchronize the carbs and followed the instructions included. I've not been able to get a reading with the unit unless the engine is running at 1600 rpm or better. This reading is minimal and only with the centre piece turned in about as far as it will go. Very hit and miss process. There is absolutely no movement of the float when the car is idling. Am I missing something? Thanks for any input. Steve
|
||||||||||||||
| |||||||||||||||
| Posted: 08-01-2007 11:22 am |
|
2nd Post |
|
Dan (Florida) Member
|
check the little pipe that goes into the side of the unysin to make sure it isn't blocked. I had one once that was with worse results than that. I think that it's also a good idea to blip the throttle with the air cleaners off and watch both slides to see if they move the same. With both carbs adjacent you can observe quite a bit even without a unysin. hth Dan
|
|||||||||||||
| ||||||||||||||
| Posted: 08-01-2007 05:25 pm |
|
3rd Post |
|
Jensen Healey Super Moderator 
|
If you have Dellorto Carbs, (did Canadian cars have Dells?) the Unisyn is not sensitive enough to take decent readings. It also alters the operation of the engine because it blocks the airflow to the cylinder being measured. Search for 4 tube manometer in old posts. The Strombergs two cylinders per carb make the Unisyn readings possible. If you need to, adjust the carbs at 1600 rpm and reduce the idle afterwards.
|
||||||||||||||
| |||||||||||||||
| Posted: 08-01-2007 10:47 pm |
|
4th Post |
|
Steve Jarvis Member
|
The pipe is not blocked and the float does move. The carbs are Strombergs and as much as my son would like the Dellortos we're going to stick with these for a while. It just seems there is not enough air moving through to pull the float up. At 1800 rpm with the centre piece closed down the float moves up to the first mark. The issue with this is the air flow is so restricted the motor starts to die out.
|
|||||||||||||
| ||||||||||||||
| Posted: 08-01-2007 11:55 pm |
|
5th Post |
|
Steve Jarvis Member
|
I think I have resolved the problem. The cap on the top of the Unisyn does not have a proper seal so there is a leak between the two tubes. I didn't notice the gap previously and there is enough room to slip in about 3 sheets of paper. Trust the replacement will do the trick.
|
||||||||||||||
| |||||||||||||||
| Posted: 08-02-2007 03:00 pm |
|
6th Post |
|
Judson Manning Member 
|
I threw away my Unisyn years ago and find balancing the carb by ear is much more effective. Of course you need to be sure both carbs are in good working condition regardless of technique. Anything else wrong with the engine makes balancing the carbs a moot exercise. The manual details how to get an initial setting using the balance screw. After that, it's just a question of blipping the throttle and making minute adjustments until both carb sound about the same.
|
|||||||||||||
| ||||||||||||||
| Posted: 09-01-2007 04:56 am |
|
7th Post |
|
pbahr Member 
|
Steve, If you insist on using such a tool, throw away the UniSyn and buy a Schleyer from JCWhitney for $29.99. Cataloge # 882792. No problems, mate. YELODOG
|
||||||||||||||
| |||||||||||||||
| Posted: 09-06-2007 09:10 pm |
|
8th Post |
|
Frank Schwartz Guest
|
I had two of those floating ball jobs and they performed so badly that I gave them away. I bought (at of all places from J.C. Whitney) a German made unit that actually has a dial gauge on it and can be adjusted to read at idle or higher RPMs, too. . I can actually breathe through it and it will give a reading. It's about thirty bucks and worth, at least to me, three times that. I can give you the J.C. Whitney stock number if you really want a gauge you can easily read and you don't have to have the engine revved up to get a reading... Why people hang with that floating ball thing is beyond me. I had to have the engine revved up to get a reading on either of the units and at idle, to get a reading, it almost choked the engine to a stop..... they are no longer in my shop and I am so glad.....
|
|||||||||||||
| ||||||||||||||
| Posted: 09-19-2007 02:05 am |
|
9th Post |
|
Steve Jarvis Member
|
I found it on their site and it is en route. Thanks for the suggestion. I have it now and finally had a chance to try it out. Much nicer than the uni-syn. Very sensitive as the needle moves with only an 1/8 to a 1/4 turn of the adjustment screw. Both carbs are no balanced and it seems to run much smoother. Thanks again. Last edited on 10-28-2007 10:58 pm by Steve Jarvis |
||||||||||||||
| |||||||||||||||
| Current time is 01:07 pm | |
| > Jensen Healey & Jensen GT Tech > Carburetors > Uni-Syn Balancer | Top |
