| ||||
| ||||
| Moderated by: Greg Fletcher |
|
||||||||||||||
| Timing Belt Adjuster & HTD Conversions | Rate Topic |
| Author | Post |
|---|
| Posted: 11-04-2006 03:25 pm |
|
1st Post |
|
Dan Eiland Member
|
I'm getting ready to begin rebuilding my engine and upgrading to the 2.2L crank. I just ordered the adjustable HTD cam gear set and was wondering if I need to change out the original timing belt adjuster to a newer style? I was going to leave my original and just install new bearings. Wondering what others have done? Dan
|
||||||||||||||
| |||||||||||||||
| Posted: 11-04-2006 08:11 pm |
|
2nd Post |
|
Jim Ketcham Member
|
Dan, I used my original tensioners with new bearings on my engines. So far I have not had any problems. I would like to know the advantages of the newer tensioners if someone can comment. Jim
|
|||||||||||||
| ||||||||||||||
| Posted: 11-06-2006 03:24 pm |
|
3rd Post |
|
Brett Gibson JH5 20497 Member
|
The tensioner that I have and the GT's use is just a single bearing, that is the width of the belt, and is adjusted with a couple of wrench's, one to turn the "cam" the bearing is on, and the other to lock it in place. I understand the older tensioner is made up of two bearings instead and requires a special tool,???. Brett.
|
||||||||||||||
| |||||||||||||||
| Posted: 11-06-2006 04:11 pm |
|
4th Post |
|
Jim Ketcham Member
|
Thanks Brett. It appears there are at least three types of tensioners. The original, with two bearings that required the "special wrench" to slip behind the pulley to adjust. The next generation, with 2 bearings that allowed adjustment from the front. The latest, single bearing (non-replaceable bearing?) that adjusts from the front. Sounds to me like the second generation one with the replaceable bearings and the easy adjustment is preferable. Jim
|
|||||||||||||
| ||||||||||||||
| Posted: 11-06-2006 05:17 pm |
|
5th Post |
|
Brett Gibson JH5 20497 Member
|
Jim, the larger single bearing is a replaceable item, it just cost's (pun intended) twice as much as the double.
|
||||||||||||||
| |||||||||||||||
| Posted: 11-06-2006 05:24 pm |
|
6th Post |
|
Ron Earp Member 
|
Does anyone make a conversion to run a modern spring loaded tensioner or an oil pressure driven one? It'd be difficult to imagine getting a proper spring loaded one in that tight of an area but figured I'd ask. R
|
|||||||||||||
| ||||||||||||||
| Posted: 11-07-2006 03:09 am |
|
7th Post |
|
Sylva Member
|
Dan I run a manual belt adjustor off an early 910 turbo, (Ok but the gauge to check the tension is expensive) on my late 910 Block. Any way I have acomplete 911 Sunbeam spring tension system in the house, In view of the info you've given me I'm happy to snd it to you for free if you pay postage, and it fits a907. (wont be much) You have my email let me know if you want it. In view of his latest Post maybe Ron could tell us if the 911 spring tensioner will fit? Kelvin
|
||||||||||||||
| |||||||||||||||
| Posted: 11-07-2006 04:54 am |
|
8th Post |
|
Dan Eiland Member
|
Kelvin, Appreciate the offer and I would be interested if there is some advantage over the style I have. I have two and the look alike. Both are from 1974 engines. I guess I could take one apart to find out what kind I have. I just assumed they both used the two bearing system. Would rather have the kind that adjust from the front to simplify the adjustments when the time comes. Anyone know if Kelvins adjuster will work on my car and if it is worth doing the conversion? BTW, Kelvin, I have some more information I'll send your way on the 9XX series engine.
|
|||||||||||||
| ||||||||||||||
| Posted: 11-13-2006 06:53 am |
|
9th Post |
|
Dan Eiland Member
|
I just removed the tensioner tonight and it is like what Jim described, there are two nuts on the front side. One is to tighten the tensioner in place and the other is to make your adjustments. Counterclockwise seems to loosen the tensioner. I need to finish tearing down my engine so I can take it to the machine shop this week to have the dowels added around the ten bolts surrounding the main bearings. If things go well this week maybe I can pull the tensioner apart to see if it has one bearing or two. My HTD cam gear set arrived earlier this week and it looks great.
|
||||||||||||||
| |||||||||||||||
| Posted: 11-13-2006 03:19 pm |
|
10th Post |
|
Ron Earp Member
|
Sylva, So what I need is a 911 spring tensioning system? I have not seen them before and will try and locate a source for one. I'd be willing to give it a go and make it fit, just have to locate it. I also thought about a simple system like the Mazda miata has, but if there is something that is close to fitting then I'd go that route first. Ron
|
|||||||||||||
| ||||||||||||||
| Posted: 11-14-2006 12:06 am |
|
11th Post |
|
Dan Eiland Member
|
Ron, have you seen the tensioner on ebay that is for sale? Lppks nothing like the one I have on my engine. http://cgi.ebay.com/ebaymotors/Belt-Tensioner-Lotus-Esprit-Eclat-Elite-Jensen-Healey_W0QQcmdZViewItemQQcategoryZ46098QQihZ020QQitemZ300047113728QQrdZ1
|
||||||||||||||
| |||||||||||||||
| Posted: 11-14-2006 12:50 am |
|
12th Post |
|
Sylva Member
|
Ron I have a picture of the ensioner with me today, it is used on the Sunbeam, Esprit S3 and Eclat SE to my knowledge, You can get them second hand from Lotus bits in the UK. Send me an email to willia@petronas.com.my and I'll send the picture, it is to big to attach.
|
|||||||||||||
| ||||||||||||||
| Posted: 11-14-2006 01:01 am |
|
13th Post |
|
Ron Earp Member
|
Click Dan's link above, is it like that? Ron
|
||||||||||||||
| |||||||||||||||
| Posted: 11-14-2006 01:33 am |
|
14th Post |
|
Sylva Member
|
Sorry can't click to ebay as I'm in work and not llowed, my privite internet is off as I'm moving house.
|
|||||||||||||
| ||||||||||||||
| Posted: 11-14-2006 03:35 am |
|
15th Post |
|
Dan Eiland Member
|
Ron, I looked at Sylva's tensioner and it looks to be the same as the one on ebay. Don't know if the one on ebay is a good buy or bad. Just trying to figure out what is available and which is the best and why.
|
||||||||||||||
| |||||||||||||||
| Current time is 11:16 pm | |
| > Jensen Healey & Jensen GT Tech > Engine & Transmission > Timing Belt Adjuster & HTD Conversions | Top |
