| ||||
| ||||
| Moderated by: Greg Fletcher | Page:   1 2 |
|
|||||||||||||
| 5-Speed Getrag Value? | Rating: 
|
| Author | Post |
|---|
| Posted: 12-10-2010 01:25 am |
|
21st Post |
|
Steve Johnson Member 
|
Yes, I fitted a clutch from a toyota celica, this fits the splines on the w-58,(drilled flywheel for pressure plate), clutch is a little bigger than original, i did convert to a hydraulic clutch master and slave cylinder as the lotus excel was hydraulic although others have done the clutch cable as original, also had to have made a pilot bearing, and rework transmission mounts on back of trany. also had to make a custom drive shaft. All in all, this in my opinion is a great upgrade. Steve
|
||||||||||||||
| |||||||||||||||
| Posted: 12-14-2010 03:53 am |
|
22nd Post |
|
superk83 Member
|
About how much did that bell housing cost? I didn't see any listed on lotus bits... maybe i'll shoot mike an email.
|
|||||||||||||
| ||||||||||||||
| Posted: 12-15-2010 12:40 pm |
|
23rd Post |
|
Steve Johnson Member
|
Just checked lotusbits.com and price is listed at 150 british lbs sterling. http://lotusbits.com/excel_chassis.html check out website, Steve
|
||||||||||||||
| |||||||||||||||
| Posted: 12-15-2010 01:03 pm |
|
24th Post |
|
superk83 Member
|
Listed under chassis parts? That would be why I didn't find it... lol! The year that's listed is for the Excel, would you use the same year w58 as excel? Last edited on 12-15-2010 01:11 pm by superk83 |
|||||||||||||
| ||||||||||||||
| Posted: 12-15-2010 09:35 pm |
|
25th Post |
|
Steve Johnson Member
|
What i used was a 1986 1/2 toyota supra mark 11 non turbo, that way the location of the shifter is correct, Steve
|
||||||||||||||
| |||||||||||||||
| Posted: 12-16-2010 05:03 am |
|
26th Post |
|
superk83 Member
|
So if I have an '84 Supra, get an '84(or pre-88)bell housing...?
|
|||||||||||||
| ||||||||||||||
| Posted: 06-01-2011 04:46 pm |
|
27th Post |
|
StevenD57 Member 
|
Steve Johnson wrote: Yes, I fitted a clutch from a toyota celica, this fits the splines on the w-58,(drilled flywheel for pressure plate), clutch is a little bigger than original, i did convert to a hydraulic clutch master and slave cylinder as the lotus excel was hydraulic although others have done the clutch cable as original, also had to have made a pilot bearing, and rework transmission mounts on back of trany. also had to make a custom drive shaft.Can you please provide some more details about exactly which Toyota Celica clutch you used? I recently got a the right bellhousing and a W58 transmission and I am trying to piece together the other bits. Is it possible to find a 8.5 inch clutch disc I can use with the original JH four speed or five speed pressure plate that will fit the splines of the Toyota W58?
|
||||||||||||||
| |||||||||||||||
| Posted: 06-01-2011 06:28 pm |
|
28th Post |
|
Steve Johnson Member
|
What I used was a clutch and pressure plate from a 81-85 toyota celica, 8 7/8" with a 21 spline hub, had the flywheel drilled and balanced to mount the clutch to flywheel. I believe you could have a custom clutch disc made, i did check and cost was about the same as disc and pressure plate for toyota. the toyota is a bit larger than the jensen, and the one i have has alot more clamping lbs the the original. i got a 6 puck racing setup and am experiencing some clutch chatter, that i don't like. Steve
|
|||||||||||||
| ||||||||||||||
| Posted: 06-01-2011 06:33 pm |
|
29th Post |
|
StevenD57 Member
|
So do you think the clutch chatter is because of the type of disc you are using or what?
|
||||||||||||||
| |||||||||||||||
| Posted: 06-01-2011 06:49 pm |
|
30th Post |
|
Steve Johnson Member
|
Not sure, but may have been a problem when installing transmission, as did not bolt up right away, and was left hanging overnight, just hanging from clutch disc and this may have caused the disc to bend a little.
|
|||||||||||||
| ||||||||||||||
| Current time is 05:49 am | Page: 1 2 |
| > Jensen Healey & Jensen GT Tech > Engine & Transmission > 5-Speed Getrag Value? | Top |
