| ||||
| ||||
| Moderated by: Greg Fletcher |
|
||||||||||||||
| 123ignition | Rate Topic |
| Author | Post |
|---|
| Posted: 08-07-2008 10:09 pm |
|
1st Post |
|
subwoofer Member
|
In theory these units from 123ignition.nl should give most of the advantages of a crankfire system while not looking out of place. A vacuum advance (with gearshift retard) unit should be a fine replacement for the stock distributor. Has anyone tried these units? Not cheap, but still cheaper than a Megasquirt, which would be one of the cheapest options for crankfire ignition, right? -- Joachim
|
||||||||||||||
| |||||||||||||||
| Posted: 08-08-2008 09:38 am |
|
2nd Post |
|
Harkes Member 
|
Hi Joachim, i was once interested in these because my relatively new Aldon Automotive distributor was leaking oil over the shaft. Then i heard that some people weren't vary satisfied with the 123ignition distributors so it made me doubt. Also the Lotus requires a different distributor then other classic cars. My leaking distributor was missing a (2nd) bearing inside, which is normal for other cars but the Lotus engine needs this bearing!! Would 123ignition know this? the people at Aldon had forgotten about it even... Then i thought: i already have the Pertronix Ignitor II and MSD6a so why don't i send back my leaking distributor to Aldon... I did. Aldon fixed it (..the bearing) and gave it the best suitable curve for my 2.2L engine. So why have 16 curves when only one does the job best? If you really want to beat this then I'd suggest the more expensive route to crankfired ignition. good luck Erik
|
|||||||||||||
| ||||||||||||||
| Posted: 08-08-2008 09:47 am |
|
3rd Post |
|
subwoofer Member
|
My distributor really needs some work now, either the springs are weak or the weights are sticking, because I get an awful amount of advance even at idle after revving a bit (still running Strombergs, but with vacuum retard plugged). I'll heed your advice and stay clear. At the moment, I will just live with it till the winter at least, since I am having some issues with the authorities. They would only allow me to register it as a historic vehicle (i.e. no mods allowed) until I produce documentation that the stock vehicle satisfies the technical requirements in effect in Norway in 1974. Do you have any idea of where to get hold of those papers? Quite a few cars where sold in Germany, maybe the TüV did a type certification on it? -- Joachim
|
||||||||||||||
| |||||||||||||||
| Posted: 08-08-2008 10:01 am |
|
4th Post |
|
Harkes Member
|
what are the technical requirements for cars in Norway in 1974? if you know these we can look for documentation I think many of it can already be found in the Jensen Healey Manual, but otherwise there is a wealth of information here on the board
|
|||||||||||||
| ||||||||||||||
| Posted: 08-08-2008 10:06 am |
|
5th Post |
|
Harkes Member
|
BTW why is your vacuum retard plugged? you are still running Strombergs...which means you need the vacuum retard. If you are running the dellorto's then you'd need to plug the vacuum retard. Just forgot to say that on the http://www.jhps.com Greg sells fantastic reconditioned Lucas distributors for both strombergs and dellorto jensen healey's. So if you decide you need a new one, this might be an option for you
|
||||||||||||||
| |||||||||||||||
| Posted: 08-08-2008 10:07 am |
|
6th Post |
|
subwoofer Member
|
I'm trying to figure out that part for myself... :-) Brake performance is the kicker. It has to be a declaration from the manufacturer or a test report from an independent laboratory (this would be where TüV fits in). It is likely to be the exact same requirements as the German ones from the same period, importing cars from mainland Europe is rarely a problem. My car came from the US, which just makes it that much more difficult. I'm up against bureaucracy here... Last edited on 08-08-2008 10:08 am by subwoofer |
|||||||||||||
| ||||||||||||||
| Posted: 08-08-2008 10:12 am |
|
7th Post |
|
Harkes Member
|
i see. It must have been done before one would say. i'll have a look around see if i can find anything.
|
||||||||||||||
| |||||||||||||||
| Posted: 08-08-2008 10:18 am |
|
8th Post |
|
subwoofer Member
|
Why I plugged the vacuum retard? It was already plugged when I got it, and I have been too busy plugging leaks elsewhere to start opening stuff up again... :-) I'm not going to buy a new distributor at this time, I am planning to build somethink similar to your engine, but then I have to get through the red tape first. If I can't find a way through, I'll consider it.
|
|||||||||||||
| ||||||||||||||
| Posted: 08-08-2008 10:30 am |
|
9th Post |
|
Harkes Member
|
that will be nice project. Hope you get through the red tape!! good luck
|
||||||||||||||
| |||||||||||||||
| Current time is 05:46 am | |
| > Jensen Healey & Jensen GT Tech > Engine & Transmission > 123ignition | Top |
