| ||||
| ||||
| Moderated by: Greg Fletcher |
|
||||||||||||||
| Looking for a Boot (trunk) lock | Rating: 
|
| Author | Post |
|---|
| Posted: 01-15-2008 12:43 am |
|
1st Post |
|
dthewlis Member
|
I'm looking for a replacement boot lock for a 1974 J-H. My car (19299) came without one. It came from Southern California where a hole into the boot didn't much matter (except for it not being locked), but it rains up here... Delta hasn't got one at all and doubts they will find another. Anyone on this board have an extra, or know where one might be found? Thanks, Dave Thewlis (Humboldt County, California)
|
||||||||||||||
| |||||||||||||||
| Posted: 01-15-2008 02:29 pm |
|
2nd Post |
|
colinw59 Member 
|
Hi Dave Try British Masters located in CA, 1-800-333-0461 or at bmr@4d.net. They're a tad expensive but Erik has lots of parts for all sorts of British sports cars. Or Richard Appleyard UK at 011-44-115-9325-320 or at http://www.jensen.co.uk Don't forget to ask for a key to or you'll have a real problem! Good luck, Colin
|
|||||||||||||
| ||||||||||||||
| Posted: 03-06-2008 01:48 am |
|
3rd Post |
|
dthewlis Member
|
I managed to get a boot lock from Richard Appleyard in the U.K. http://www.jensen.co.uk/. However it came without the "spring" - which I guessed meant a spring to return the keyhole to the upright position. Unfortunately it appears to mean the piece which secures the lock into position. Not shown in the parts manual or Delta's reductions as far as I can find. Anybody out there have the requisite piece to secure the lock? I'd be delighted to acquire it!
|
||||||||||||||
| |||||||||||||||
| Posted: 03-30-2008 05:41 am |
|
4th Post |
|
pbahr Member 
|
Dave, Did you ever get this problem solved??? I may have some Boot Lock bits in my garage, and I can look if you are really stuck. Pete Bahr. YELODOG
|
|||||||||||||
| ||||||||||||||
| Posted: 03-30-2008 02:56 pm |
|
5th Post |
|
dthewlis Member
|
Hi Pete, so far I'm stuck. Complicated by their being no Jensen Healeys in the area - so I can't see what I am supposed to have, and the available diagrams are not informative. So I would definitely appreciate any help very much. What I have right now is the lock unit, with the cylinder, and the rotating nylon cam at the bottom. (And a key.) Thanks! Dave
|
||||||||||||||
| |||||||||||||||
| Posted: 03-30-2008 03:32 pm |
|
6th Post |
|
pbahr Member
|
Dave, Exactly what parts do you need??? Pete
|
|||||||||||||
| ||||||||||||||
| Posted: 03-30-2008 03:49 pm |
|
7th Post |
|
dthewlis Member
|
That's my problem! I have no way of knowing what I don't have because I can neither examine an existing J-H to see what's there or reference a diagram or picture that explains it. When I push the lock unit that I have into the hole in the boot lid, it slides in but nothing holds it in place. I am guessing that there is some kind of retaining spring or lock that it is supposed to slide into that secures it in place (presumably from underneath) and maybe other bits as well, but I don't know. When I try to hold the lock in place with my fingers and turn the key, the cam rotates but doesn't seem to press against the spring-loaded latch that opens the trunk, so there may be something else missing as well, but I can't tell. Sort of a catch-22, huh? Last edited on 03-30-2008 03:50 pm by dthewlis |
||||||||||||||
| |||||||||||||||
| Posted: 03-30-2008 05:00 pm |
|
8th Post |
|
pbahr Member
|
Dave, Can you send me photos of what you have? Semd to peteb01@comcast.net Pete
|
|||||||||||||
| ||||||||||||||
| Posted: 03-30-2008 05:16 pm |
|
9th Post |
|
dthewlis Member
|
Will do a little later today. Thanks! Dave
|
||||||||||||||
| |||||||||||||||
| Posted: 06-25-2021 10:11 pm |
|
10th Post |
|
DonBurns Member
|
Is there any new info on bot locks out there? Putting 15800 back together and discovered that the boot lock was missing the clip, and was silicone'd in place. Delta does not have. I was hoping the clips for the door locks were the same, but they are not. Does anybody know where to get? Were the boot locks common to any other car?
|
|||||||||||||
| ||||||||||||||
| Posted: 06-26-2021 03:51 pm |
|
11th Post |
|
noomg Member
|
Don, In the 13 years since the last post of this thread I don't think anything has changed. What you're looking for is a barrel spring that fits around the lock barrel, it has two tabs that point up and flair out. With a properly complete lock unit you push it through the deck lid hole and the tabs snap the unit into place. The barrel spring is usually what fails. You've got a couple of options, try to get a used one, Bruce(Red Racer)might have one or give British Masters a try. Also, as strange as it sounds there's a possibility you could find a new one through one of the small specialist shops in England. Rejen, for example does mainly interiors but they also do complete restorations and carry a lot of odd bits for Jensen-Healey.
|
||||||||||||||
| |||||||||||||||
| Posted: 06-26-2021 05:49 pm |
|
12th Post |
|
redracer Member
|
Don: have plenty(used); a little tricky to install, but I could SKYPE you through the installation. Also, you will want to cut a small piece off the latch so the lock will open easily(I imagine this was the main reason people took them out, although the fix is quite easy) bruce/RedRacerbm@gmail 404-261-2552(land line--no texts) SKYPE name: RockClimber52
|
|||||||||||||
| ||||||||||||||
| Posted: 06-26-2021 08:18 pm |
|
13th Post |
|
DonBurns Member
|
Bruce- Thanks! I am getting car back from body shop Monday. They said they would figure out something to put the lock in. I'll see what they did and decide if I want to "fix" it then.
|
||||||||||||||
| |||||||||||||||
| Current time is 12:15 am | |
| > Jensen Healey & Jensen GT Tech > Body & interior stuff > Looking for a Boot (trunk) lock | Top |
