| ||||
| ||||
| Moderated by: Greg Fletcher |
|
||||||||||||||
| Lockheed Wheel cylinders | Rate Topic |
| Author | Post |
|---|
| Posted: 09-09-2021 06:40 pm |
|
1st Post |
|
redracer Member
|
Although this can be quite a chore without the well thought-out plan, here is the way I have been doing it for over 40 years(doesn't mean the "right way" or "Only way"). Making a 2X4 to fit the approximate shape of the wheel cylinder and reinforcing it with a piece of angle iron, should help with installing the troublesome circlip on the backing plate. pleas note that this circlip goes on the more "difficult" way. MOSS makes a tool for this, which I purchased a few years ago, but it does NOT work very well--I bent over 3 circlips before I went back to my old method. One other item: the snap ring pliers are from WIHA(German tools) and have a little groove cut into the ends to capture and hold the circlip. The cheap ones from Harbor Freight, etc, will likely slip as your using them, but I did use that cheaper style for years before getting the WIHA ones. Attachment: J-H Lockheed wheel cylinder installation.jpg3s.jpg (Downloaded 45 times)
|
||||||||||||||
| |||||||||||||||
| Posted: 09-09-2021 06:41 pm |
|
2nd Post |
|
redracer Member
|
[img][/img] Attachment: J-H Lockheed wheel cylinder installation.jpg1s.jpg (Downloaded 46 times)
|
|||||||||||||
| ||||||||||||||
| Posted: 09-09-2021 06:41 pm |
|
3rd Post |
|
redracer Member
|
[img][/img] Attachment: J-H Lockheed wheel cylinder installation.jpg2s.jpg (Downloaded 46 times)
|
||||||||||||||
| |||||||||||||||
| Posted: 09-09-2021 06:42 pm |
|
4th Post |
|
redracer Member
|
[img][/img] Attachment: J-H Lockheed wheel cylinder installation.jpg4s.jpg (Downloaded 45 times)
|
|||||||||||||
| ||||||||||||||
| Posted: 09-09-2021 06:42 pm |
|
5th Post |
|
redracer Member
|
[img][/img] Attachment: J-H Lockheed wheel cylinder installation.jpg5s.jpg (Downloaded 45 times)
|
||||||||||||||
| |||||||||||||||
| Posted: 09-09-2021 06:42 pm |
|
6th Post |
|
redracer Member
|
[img][/img] Attachment: J-H Lockheed wheel cylinder installation.jpg6s.jpg (Downloaded 46 times)
|
|||||||||||||
| ||||||||||||||
| Posted: 09-09-2021 06:43 pm |
|
7th Post |
|
redracer Member
|
[img][/img] Attachment: J-H Lockheed wheel cylinder installation.jpg7s.jpg (Downloaded 45 times)
|
||||||||||||||
| |||||||||||||||
| Posted: 09-09-2021 06:44 pm |
|
8th Post |
|
redracer Member
|
[img][/img] This a a 12 point 17mm socket that I filed down the end to get the circlip fully engaged onto the slot in the wheel cylinder Attachment: J-H Lockheed wheel cylinder installation.jpg8s.jpg (Downloaded 44 times)
|
|||||||||||||
| ||||||||||||||
| Posted: 09-09-2021 06:44 pm |
|
9th Post |
|
redracer Member
|
[img][/img] Attachment: J-H Lockheed wheel cylinder installation.jpg9s.jpg (Downloaded 44 times)
|
||||||||||||||
| |||||||||||||||
| Posted: 09-09-2021 06:46 pm |
|
10th Post |
|
redracer Member
|
[img][/img] Please note the circlip has all 3 tabs fully onto the slot in the wheel cylinder. A little smearing of grease will help slide it around the the slot, etc. Hope this helps, bruce Attachment: J-H Lockheed wheel cylinder installation.jpg10s.jpg (Downloaded 44 times)
|
|||||||||||||
| ||||||||||||||
| Current time is 06:08 am | |
| > Jensen Healey & Jensen GT Tech > Brakes > Lockheed Wheel cylinders | Top |
