| ||||
| ||||
| Moderated by: Greg Fletcher |
|
||||||||||||||
| Metric? | Rate Topic |
| Author | Post |
|---|
| Posted: 02-22-2013 08:41 pm |
|
1st Post |
|
sholdowa Member 
|
I've just suffered a catastrophic brake failure... Master cylinder needs a rebuild I think. First step was to drain the system, as the fluid is probably 10 years old anyway. Fronts... Np problem. Rears were a different matter, and the bleed nipple sheared off. So, time to replace both rear cylinders, I think. Didn't have a brake spanner, so tried the best open ended spanner on the brake pipe, to no avail. The manual tells me these fittings are metric. Is this true? Am surprised for a Brit car of this vintage. Can anyone confirm this for me, please? Also, does anyone have part nos for the wheel cylinders and master rebuild kits? I was going to take them in to be sure.
|
||||||||||||||
| |||||||||||||||
| Posted: 02-22-2013 10:23 pm |
|
2nd Post |
|
JodyKerr Member 
|
In the united states most brake fittings use SAE tools
|
|||||||||||||
| ||||||||||||||
| Posted: 02-22-2013 11:15 pm |
|
3rd Post |
|
Jensen Healey Super Moderator 
|
The brake fittings fit a 7/16" wrench. A standard open end spanner can distort the flare nut. Proper brake wrenches have the head angled a bit so you can work around obstructions, a small but good investment. The Lotus engine is metric except for the drain plug which is 3/4 Whitworth. The rest of the car is SAE.
|
||||||||||||||
| |||||||||||||||
| Posted: 02-23-2013 03:32 am |
|
4th Post |
|
sholdowa Member
|
I ended up using one of those fit all spanners - all teeth and tightens the harder you pull. The manual says 10mm but it's certainly 7/16 AF. Master cylinder is completely different too! It's got 08 646979175 G cast into it. Any idea what it is?? Glad I decided to take the bits down to the motor factors! Last edited on 02-23-2013 05:33 am by sholdowa |
|||||||||||||
| ||||||||||||||
| Posted: 02-25-2013 08:19 pm |
|
5th Post |
|
subwoofer Member
|
have you googled the part number? I got a new master cylinder a few years back, was listed for a Land Rover IIRC. Was about £50. -- Joachim
|
||||||||||||||
| |||||||||||||||
| Posted: 02-25-2013 08:44 pm |
|
6th Post |
|
sholdowa Member
|
Hi Joachim, Yes, it was the first thing I did, but no luck. I see a few that will fit... TR6, and a couple of Landy ones. I assume the difference is in the piston sizes, but can find no info on that. Also, as the car has been raced for decades, what changes may have been made anyway! Brakes are standard apart from this, so am looking to replace a standard MC. As you say, the replacements are below GPB50, but when you add the quoted postage of GBP81, it makes your eyes water a bit! Am working through Oz Landy sites now... Cheers, Steve
|
|||||||||||||
| ||||||||||||||
| Posted: 02-25-2013 10:17 pm |
|
7th Post |
|
subwoofer Member
|
And I thought freight rates from the UK to Norway were bad... I'll grab the chance while the Pound is weak to get myself a set of front and rear discs from Hispec. -- Joachim
|
||||||||||||||
| |||||||||||||||
| Posted: 02-28-2013 08:54 pm |
|
8th Post |
|
gmgiltd Member
|
Hi Joachim , If you do go the Hispec route there are a couple of catchits. I took my car in there just over a year ago and provided them with a back axle and they measured up everything. Fronts are excellent but the rears took a bit of work with spacers and longer studs and getting the handbrake linkage right. Keep in mind that I am using 15" wheels from the club store so you will need to provide them with the accurate internal dimensions of whatever rims you intend to use. Speak to Alex - very helpfull there. Gordon
|
|||||||||||||
| ||||||||||||||
| Posted: 03-01-2013 08:09 pm |
|
9th Post |
|
sholdowa Member
|
Availability was zero down here so I'm having the mc rebuilt. $160 + tax for resleeving in stainless and a rebuild.
|
||||||||||||||
| |||||||||||||||
| Current time is 05:35 pm | |
| > Jensen Healey & Jensen GT Tech > Brakes > Metric? | Top |
