Home 
Home Search search Menu menu Not logged in - Login | Register
> Jensen Healey & Jensen GT Tech > Ignition > No Spark at all

 Moderated by: Greg Fletcher Page:    1  2  3  Next Page Last Page  
New Topic Reply Printer Friendly
No Spark at all  Rate Topic 
AuthorPost
 Posted: 10-17-2010 06:56 pm
  PM Quote Reply
1st Post
jarnol123
Member
 

Joined: 09-29-2009
Location: Scottsdale, Arizona USA
Posts: 95
Status: 
Offline
 I replaced the crane allison ignition with a pertronix ignitor. I also have a new flame thrower coil.

I still have no spark.  I took the dizzy cap off and left the ignition on and manually cranked the engine. The rotor went all the way around and still no spark.

I checked all the connections and they look fine. I'm confused. Please help!

 

 

 
Back To Top PM Quote Reply  

 Posted: 10-17-2010 07:36 pm
  PM Quote Reply
2nd Post
jarnol123
Member
 

Joined: 09-29-2009
Location: Scottsdale, Arizona USA
Posts: 95
Status: 
Offline
 OK I ran a piece of wire from the +ve battery terminal to the Coil to ensure I have 12 V..OK...still no spark when I turn over the engine.....I noticed that there is a black and white wire that goes to the -ve of the coil ...the other end isn't attached to anything ...what should that wire be attached to??
Back To Top PM Quote Reply

 Posted: 10-17-2010 08:45 pm
  PM Quote Reply
3rd Post
jarnol123
Member
 

Joined: 09-29-2009
Location: Scottsdale, Arizona USA
Posts: 95
Status: 
Offline
 Here's some pics of the solenoid and coil..

Attachment: Picture 025.jpg (Downloaded 69 times)
Back To Top PM Quote Reply  

 Posted: 10-17-2010 08:48 pm
  PM Quote Reply
4th Post
jarnol123
Member
 

Joined: 09-29-2009
Location: Scottsdale, Arizona USA
Posts: 95
Status: 
Offline
 BTW: Anyone know what this is?

Attachment: Picture 030.jpg (Downloaded 86 times)
Back To Top PM Quote Reply

 Posted: 10-17-2010 08:54 pm
  PM Quote Reply
5th Post
Jensen Healey
Super Moderator


Joined: 03-11-2005
Location: San Anselmo, California USA
Posts: 983
Status: 
Offline
 First of all, did you buy a new rotor?
Back To Top PM Quote Reply  

 Posted: 10-17-2010 09:00 pm
  PM Quote Reply
6th Post
jarnol123
Member
 

Joined: 09-29-2009
Location: Scottsdale, Arizona USA
Posts: 95
Status: 
Offline
 yes
Back To Top PM Quote Reply

 Posted: 10-17-2010 09:02 pm
  PM Quote Reply
7th Post
Jensen Healey
Super Moderator


Joined: 03-11-2005
Location: San Anselmo, California USA
Posts: 983
Status: 
Offline
 That thing with the bent contacts is an oil pressure sending unit. It's not stock. The stock setup is a small tube that carries oil all the way to the guage.
Back To Top PM Quote Reply  

 Posted: 10-17-2010 09:05 pm
  PM Quote Reply
8th Post
jarnol123
Member
 

Joined: 09-29-2009
Location: Scottsdale, Arizona USA
Posts: 95
Status: 
Offline
 Ok thanks
Back To Top PM Quote Reply

 Posted: 10-17-2010 09:13 pm
  PM Quote Reply
9th Post
jarnol123
Member
 

Joined: 09-29-2009
Location: Scottsdale, Arizona USA
Posts: 95
Status: 
Offline
 the coil...

Attachment: Picture 026.jpg (Downloaded 94 times)
Back To Top PM Quote Reply  

 Posted: 10-17-2010 09:26 pm
  PM Quote Reply
10th Post
Jensen Healey
Super Moderator


Joined: 03-11-2005
Location: San Anselmo, California USA
Posts: 983
Status: 
Offline
 Take the white with slate wire off the negative terminal. It provides 12 volts during cranking coming from the starter. It should connect to the positive side.
Back To Top PM Quote Reply

 Posted: 10-17-2010 09:28 pm
  PM Quote Reply
11th Post
Jensen Healey
Super Moderator


Joined: 03-11-2005
Location: San Anselmo, California USA
Posts: 983
Status: 
Offline
 If that wire with the red tape is the hot, connect it directly to the red Pertronix wire.

Edit: sorry, connect both the hot and the red wire to the + side of the coil.

The hot should be coming from the ballast resistor.

Last edited on 10-17-2010 09:42 pm by Jensen Healey
Back To Top PM Quote Reply  

 Posted: 10-17-2010 09:39 pm
  PM Quote Reply
12th Post
Jensen Healey
Super Moderator


Joined: 03-11-2005
Location: San Anselmo, California USA
Posts: 983
Status: 
Offline
 The Pertronix is just a switch. The hot 12 volts goes through the red Pertronix wire from the hot side of the coil. The magnetic switch in the distributor grounds the black wire (connected to the minus side) to trigger the coil.

Last edited on 10-17-2010 09:43 pm by Jensen Healey
Back To Top PM Quote Reply

 Posted: 10-17-2010 10:21 pm
  PM Quote Reply
13th Post
jarnol123
Member
 

Joined: 09-29-2009
Location: Scottsdale, Arizona USA
Posts: 95
Status: 
Offline
 OK will try that...btw I don't have a ballast resistor
Back To Top PM Quote Reply  

 Posted: 10-17-2010 10:58 pm
  PM Quote Reply
14th Post
jarnol123
Member
 

Joined: 09-29-2009
Location: Scottsdale, Arizona USA
Posts: 95
Status: 
Offline
 Tried that ...still no hint of a spark anywhere...
Back To Top PM Quote Reply

 Posted: 10-17-2010 11:42 pm
  PM Quote Reply
15th Post
Jensen Healey
Super Moderator


Joined: 03-11-2005
Location: San Anselmo, California USA
Posts: 983
Status: 
Offline
 Remove all wires from coil. Find the switched hot wire and put it on the + side. put the red wire from the Pertronix on the + side. Put the black wire from the Pertronix on the minus side.

Check spark from coil. Pull the high tension lead out of the center of the distributor cap and hold near a ground while cranking.  
Back To Top PM Quote Reply  

 Posted: 10-18-2010 02:13 am
  PM Quote Reply
16th Post
jarnol123
Member
 

Joined: 09-29-2009
Location: Scottsdale, Arizona USA
Posts: 95
Status: 
Offline
 I had to pack it up for today but I'll try this tomorrow and report back.

Thanks for all the help.
Back To Top PM Quote Reply

 Posted: 10-18-2010 02:15 am
  PM Quote Reply
17th Post
jarnol123
Member
 

Joined: 09-29-2009
Location: Scottsdale, Arizona USA
Posts: 95
Status: 
Offline
 When you say "switched" wire..which one is that?
Back To Top PM Quote Reply  

 Posted: 10-18-2010 02:17 am
  PM Quote Reply
18th Post
jarnol123
Member
 

Joined: 09-29-2009
Location: Scottsdale, Arizona USA
Posts: 95
Status: 
Offline
 also when I'm cranking is this a manual crank or not?
Back To Top PM Quote Reply

 Posted: 10-18-2010 03:37 am
  PM Quote Reply
19th Post
Jensen Healey
Super Moderator


Joined: 03-11-2005
Location: San Anselmo, California USA
Posts: 983
Status: 
Offline
 The wire from the ignition switch. It's white and goes through the tachometer and then to the ballast resistor.

On some later cars the wire has a built-in resistor and will only put out about 9 volts. What year is your car? Maybe that's why you have no ballast resistor.

Crank the car using the starter.

 
Back To Top PM Quote Reply  

 Posted: 10-19-2010 02:24 am
  PM Quote Reply
20th Post
jarnol123
Member
 

Joined: 09-29-2009
Location: Scottsdale, Arizona USA
Posts: 95
Status: 
Offline
 Mine is a 1975...I'm going to try your suggestions now...will report back
Back To Top PM Quote Reply

Current time is 08:22 pm Page:    1  2  3  Next Page Last Page    
> Jensen Healey & Jensen GT Tech > Ignition > No Spark at all Top


UltraBB 1.172 Copyright © 2007-2011 Data 1 Systems