| ||||
| ||||
| Moderated by: Greg Fletcher |
|
||||||||||||||
| Header Gasket | Rate Topic |
| Author | Post |
|---|
| Posted: 10-16-2005 10:12 pm |
|
1st Post |
|
Rory Clark Member
|
Well looks like I blew a header gasket. Have not looked under the car to see how much of a job it is going to be and the Shop manual does not even mention it. Any remarks on how to go about the replacement ? Thanks Rory 73-JH
|
||||||||||||||
| |||||||||||||||
| Posted: 10-17-2005 06:32 pm |
|
2nd Post |
|
Judson Manning Member 
|
This is one of those "while you're at" it kind of things. Like all cars, getting to the head gasket requires removing the entire intake and exhaust in order to remove the head. With the 907, you have the added task of removing the cam towers. In short, half the engine has to be disassembled. While you're at it... Now would be a good time to invest in a valve-job, possibly new valves and guides, not to mention a proper valve-shimming. Give the carbs a thorough cleaning (if not totally rebuilt), and check the condition of your headers. New belts are a must, and new tensioner bearings would be wise as would new spark plugs. A water-pump rebuild, and new thermostat wouldn't be a bad idea since the water pump has to be removed to get the head off the block. Performance wise, the new 'black' head-gasket is thicker than the original laminated steel version. You will lose ~1/2 a point in compression, however, it seals MUCH better on an engine who's nip isn't perfect. While you're at it...a pair of the club's 107 cams would not only reclaim the lost performance, but will give you increased low&mid range drivability. Why not upgrade those plug-wires, cap and rotor??? the list goes on and on.... Alternatively, you could tear everything apart, replace the head-gasket and call it a day...then wait for any of the above to cause problems later. Instead of a problem, I would view this as an opportunity for a Winter project that WILL net a very reliable engine, with a boost in drivability just in time for Spring. Trailer it on over to Georgia and I'll knock it out for you in about 4wks.... Judson Manning
|
|||||||||||||
| ||||||||||||||
| Posted: 10-17-2005 07:18 pm |
|
3rd Post |
|
Rory Clark Member
|
Judson, Sorry I mis-spoke. What I was meaning to say was the Exaust Header gasket on # 4 Rory
|
||||||||||||||
| |||||||||||||||
| Posted: 10-17-2005 10:07 pm |
|
4th Post |
|
Lawrence Tod Member 
|
Some degreaser and a descent squirt with the hose the day before is a must. You might want to consider replacing that steering column Bushing while your under there. Check the status of the bolts and lock nuts on the steering knuckles. Delta sold me some copper lock nuts with my replacement header/ exhaust Manifold, they were very nice to work with and should have a longer life compared to mild steel. Just a thought though, If I'm going under I like to get a lot done one time Lawrence
|
|||||||||||||
| ||||||||||||||
| Posted: 10-18-2005 01:42 pm |
|
5th Post |
|
Brian Kelly Member
|
Yes the copper bolts are nice and I also recommend them. To get at those header bolts it is helpful to unbolt the left motor mount and lift the left side of the engine up off the mount using a floor jack. Make sure to use some blocking. We don't want to be crushing appendages in case the jack slips out or fails. Brian
|
||||||||||||||
| |||||||||||||||
| Posted: 10-28-2005 03:10 am |
|
6th Post |
|
Esprit2 Member
|
Rory, Were you still running the stock-style of exhaust manifold to cylinder head gasket? If so, then the Lotus Esprit Turbo gaskets are a vast improvement. Put in a set of those and you won't blow 'em again. Instead of steel-asbestos-steel Oreo sandwich, they are laminated layers of thin stainless steel. Originally two laminates, then three. The three-lam is what you want. Lotus' price for their OEM parts is insane. JAE has a similar gasket that looks a little different, but works the same at a more reasonable price. Still expensive compared to the Oreo's, but very cost effective when you consider that you won't have to go through the grief of replacing them again. Good luck, Tim Engel
|
|||||||||||||
| ||||||||||||||
| Current time is 01:30 am | |
| > Jensen Healey & Jensen GT Tech > Engine & Transmission > Header Gasket | Top |
