| ||||
> Jensen Healey & Jensen GT Tech > Engine & Transmission > Anyone ever had to retrieve a nut that fell into the cam tower oil return passage? |
| ||||
> Jensen Healey & Jensen GT Tech > Engine & Transmission > Anyone ever had to retrieve a nut that fell into the cam tower oil return passage? |
| Moderated by: Greg Fletcher |
|
||||||||||||||
| Anyone ever had to retrieve a nut that fell into the cam tower oil return passage? | Rate Topic |
| Author | Post |
|---|
| Posted: 08-12-2020 01:58 am |
|
1st Post |
|
jensendriver123 Member
|
Anyone ever had to retrieve a nut that fell into the cam tower oil return passage? the most frontward nut fell into the passage and down into the engine head as I was unscrewing it to remove the cam towers. I haven't been able to find a flexible magnetic pickup tool that is small enough and long enough to fit down into the passage way. Does anybody now, do I need to pull the head? Thanks much. Richard
|
||||||||||||||
| |||||||||||||||
| Posted: 08-12-2020 01:50 pm |
|
2nd Post |
|
redracer Member
|
years ago I made up a "flexible" magnet from one of the SEARS magnet sets(bought some extra on ebay a couple of years ago because they are very useful and aren't made anymore: {VINTAGE SEARS CRAFTSMAN 4404 5-PIECE MAGNETIC SOCKET INSERT W/ POUCH: https://www.ebay.com/itm/VINTAGE-SEARS-CRAFTSMAN-4404-5-PIECE-MAGNETIC-SOCKET-INSERT-W-POUCH/362990706474?hash=item5483ee9f2a:g:~k4AAOSwCUdetwur} I cut an indent into the middle and wrapped some thin brass wire around it to drop into small/tight spaces. good luck, bruce
|
|||||||||||||
| ||||||||||||||
| Posted: 08-12-2020 02:50 pm |
|
3rd Post |
|
Steve Duncan Member
|
Yes, it happened to me as well. I cut off a piece of a magnet, so I ended up with a small rectangular piece. I then filed a groove (sort of a ring) around one end. I then tied some flexible speaker wire around the groove. Attachment: fishing magnet 300.jpg (Downloaded 65 times)
|
||||||||||||||
| |||||||||||||||
| Posted: 08-12-2020 04:05 pm |
|
4th Post |
|
jensendriver123 Member
|
Thanks Guys. Awesome Steve! I feel much better now knowing that someone else got stung by the same bee and figured out a solution. I finally did find what looks like a flexible extension magnet that might work. Should arrive in a few days. But, if it doesn't work, I'll try to fashion something like you did. Thanks much. Richard
|
|||||||||||||
| ||||||||||||||
| Posted: 09-16-2020 04:16 pm |
|
5th Post |
|
noomg Member
|
Richard, It's called learning a lesson the hard way. Mine came in 1971 at 2am installing a carburetor on VW, the nut dropped into the intake manifold, had to take it apart. Since then when there's the possibility of dropping something down an undesirable hole I either cover it with a rag or stuff it with a paper towel.
|
||||||||||||||
| |||||||||||||||
| Posted: 09-16-2020 04:20 pm |
|
6th Post |
|
noomg Member
|
Oh, and Steve, awesome fab on your retrieval tool.
|
|||||||||||||
| ||||||||||||||
| Posted: 09-17-2020 01:22 am |
|
7th Post |
|
jensendriver123 Member
|
Hi noomg, Yes, I was, after some searching, able to find a very nice tool that is, essentially, a very flexible wire with a very small but strong magnet on the end. I was able to fish that down deep into the engine and much to my amazement, it came up with the dreaded nut. And then life was good again :)
|
||||||||||||||
| |||||||||||||||
| Posted: 09-17-2020 01:24 am |
|
8th Post |
|
jensendriver123 Member
|
Hi Noomg, Yes, after some searching on the internet I finally discovered a very nice tool that had a long, flexible wire with a very small but strong magnet on the end of it. I was able to fish it deep down into the engine and, much to my amazement, it came back out with the "dreaded" nut. And then life was good again :)
|
|||||||||||||
| ||||||||||||||
| Current time is 09:03 pm | |
| > Jensen Healey & Jensen GT Tech > Engine & Transmission > Anyone ever had to retrieve a nut that fell into the cam tower oil return passage? | Top |
