| ||||
| ||||
| Moderated by: Greg Fletcher |
|
||||||||||||||
| W58 Clutch release bearing | Rating: 
|
| Author | Post |
|---|
| Posted: 03-22-2010 06:54 pm |
|
1st Post |
|
jdenglish Member
|
My first time on the road in three years after a W58 conversion was pleasant and painful. My fear is that I may have installed the clutch release bearing backwards or have experienced a premature failure. Is this a JH part, Lotus part or a Toyota part. brand and a part number? Thanks, John
|
||||||||||||||
| |||||||||||||||
| Posted: 03-23-2010 01:56 am |
|
2nd Post |
|
Jim Ketcham Member
|
I used the JH clutch bearing. My conversion to the W58 was via the Conversion Components kit.
|
|||||||||||||
| ||||||||||||||
| Posted: 03-23-2010 04:14 pm |
|
3rd Post |
|
jdenglish Member
|
I used the bearing that Colin included in kit. I'll check with the Club store or Delta for a replacement. On another topic, I was trying to find a domestic clutch plate replacement for the eventual failure, but it came up zilch.
|
||||||||||||||
| |||||||||||||||
| Posted: 03-23-2010 04:38 pm |
|
4th Post |
|
Jim Ketcham Member
|
I also could not find a suitable clutch replacement. I had ordered an extra from Colin at the time I got my kit. In the past I also had no problem getting my original JH clutch plate rebuilt locally (new friction material) so I assume I can get the hybrid JH/W58 clutch rebuilt when (if) I need it. If I recall correctly, it took about a week to have it resurfaced. Jim
|
|||||||||||||
| ||||||||||||||
| Posted: 03-23-2010 04:41 pm |
|
5th Post |
|
jdenglish Member
|
Thanks Jim, Now all I have to do is undo the last 3 months assembly work and start over.
|
||||||||||||||
| |||||||||||||||
| Posted: 03-31-2010 04:56 am |
|
6th Post |
|
Dakota123 Member
|
I haven't started on my W58 conversion, but I was concerned that the throwout bearing provided in Colin's kit may be a cheap knock-off so I did some research and found that it appears to be a well-known Japanese brand with interchange possibilities from other manufacturers. I'm traveling at pressent, but job willing I'll be home next weekend (April 3) and will post the manufacturers and numbers I came up with. Mike Last edited on 03-31-2010 05:06 am by Dakota123 |
|||||||||||||
| ||||||||||||||
| Posted: 03-31-2010 12:59 pm |
|
7th Post |
|
jdenglish Member
|
Thanks, Your concerns are well founded. Murphy's' law is not to be denied.
|
||||||||||||||
| |||||||||||||||
| Posted: 04-10-2010 09:52 pm |
|
8th Post |
|
Dakota123 Member
|
The Conversion Component kit (mine, anyway!) uses a Nachi throwout bearing, 40 TRK30W 2SB. This converts to NSK TK40-16AU3 and SKF VKC-3578 The Nachi dimensions are 70x40x18.5. The dimensions of the cross-referenced brands differred (except for ID). Hope this helps... Mike
|
|||||||||||||
| ||||||||||||||
| Posted: 04-11-2010 07:39 pm |
|
9th Post |
|
jdenglish Member
|
Mike, "Dimensions differed"? How then would it be an exact replacement?
|
||||||||||||||
| |||||||||||||||
| Posted: 04-11-2010 09:15 pm |
|
10th Post |
|
Dakota123 Member
|
They are listed as interchange by the manufacturers (not me personally) and are not necessarily exact replacement. For a throwout bearing, as long as the shaft fit is correct there are different bearings that will physically work but differ in width or OD by a mm or so. Sorry I can't be of more help. Mike
|
|||||||||||||
| ||||||||||||||
| Posted: 04-12-2010 02:24 am |
|
11th Post |
|
jdenglish Member
|
Your help will be validated when you put your finger in the wound and tell the heretics that all is well with whatever bearing you choose
|
||||||||||||||
| |||||||||||||||
| Posted: 04-12-2010 02:46 am |
|
12th Post |
|
Dakota123 Member
|
Not sure what I did to offend you. I had some information of possible use and I gave it. As I said, the manufacturers themselves list them as replacements, not me personally. Mike
|
|||||||||||||
| ||||||||||||||
| Posted: 04-12-2010 04:03 am |
|
13th Post |
|
jdenglish Member
|
Mike, No offense ever taken, were just exchanging information. The paths we've taken will solve the problems. it's the translations that seem to confusing. Greg Fletcher's great quote from wartime England "Remain calm and carry on" John
|
||||||||||||||
| |||||||||||||||
| Posted: 06-06-2010 05:24 pm |
|
14th Post |
|
jdenglish Member
|
Mike, Be sure to install a new Toyota transmission extension housing oil seal for the drive shaft tail piece. The one that came with the CC kit was externally rusty and of course leaked. Just over 11 bucks from Toyota.
|
|||||||||||||
| ||||||||||||||
| Posted: 06-07-2010 04:44 pm |
|
15th Post |
|
Dakota123 Member
|
Thanks for the tip. Are you to the point where it's going back together?
|
||||||||||||||
| |||||||||||||||
| Posted: 06-07-2010 04:56 pm |
|
16th Post |
|
jdenglish Member
|
I had a slight hiccup. My 5-speed 3:42 ratio rear end was too tall so I had to track down a 4-speed with a 3:73 ratio. Found one in Riverside had it blasted clean, painted and was going to mount the drum brakes from the 5 speed. Although relatively new when the project was started, the shoes were glazed and had a weird wear pattern. Fortunately the new rear end seems to have less backlash that the old one. Next stop was a disc brake conversion from Vermont. (A $1k story in itself) Just finished the install last week. During road tests the suspect throwout bearing did not squeal so maybe it will be all right-who knows? The tranny did develop a rear seal leak so that's the next windmill to tilt at. The W58 gear box is a delight.
|
|||||||||||||
| ||||||||||||||
| Posted: 06-07-2010 05:21 pm |
|
17th Post |
|
Dakota123 Member
|
Sounds like major progress and a net upgrade to boot. I'm finally back to more of a routine at home after spending virtually all winter and spring out of state. I'm hopeful that I will be able to finally get back to work on 10628. Mike
|
||||||||||||||
| |||||||||||||||
| Posted: 07-02-2010 01:25 am |
|
18th Post |
|
jdenglish Member
|
Be sure to check the diameter of your drive shaft yoke as Colin may have shipped one from a different source. My transmission seal is 58mm OD and a 38mm ID. For those dimensions, the seal should is a Toyota 90311-38032 SEAL TYPE T OIL List price was 13.49
|
|||||||||||||
| ||||||||||||||
| Posted: 01-26-2011 04:36 am |
|
19th Post |
|
pbahr Member 
|
Hi guys, I have a need for the Shifter Assy that fits Getrag five speed Transmissions. Don’t want the tranny, just the Shifter Assy. If you know of anyone that might have such an item, send me a direct email. Any help, or leads, would be appreciated, Pete Bahr peteb01@comcast.net
|
||||||||||||||
| |||||||||||||||
| Current time is 10:27 pm | |
| > Jensen Healey & Jensen GT Tech > Engine & Transmission > W58 Clutch release bearing | Top |
