| ||||
| ||||
| Moderated by: Greg Fletcher |
|
||||||||||||||
| 73 #11928 | Rate Topic |
| Author | Post |
|---|
| Posted: 03-18-2018 06:23 pm |
|
1st Post |
|
rbcnewfield Member
|
Hello members, I am a new owner to J-H's, I always have interest in unique cars so I purchased this 73 online out of long term dry storage in Utah and brought it to Maine. Primarily complete but missing a few pieces (air box and some interior trim). Seller had fired it on ether but that's it. Attachment: 73 jensen project (9).JPG (Downloaded 170 times)
|
||||||||||||||
| |||||||||||||||
| Posted: 03-18-2018 06:24 pm |
|
2nd Post |
|
rbcnewfield Member
|
First task was to replace the timing belt and tensioner bearings, also replace all fluids Attachment: 73 jensen project (13).JPG (Downloaded 167 times) Last edited on 03-18-2018 06:28 pm by rbcnewfield |
|||||||||||||
| ||||||||||||||
| Posted: 03-19-2018 05:52 pm |
|
3rd Post |
|
redracer Member
|
Possibly the fuel pump? If you have the original SU, do NOT throw it away. They are more reliable and quieter than most, and if you do need a new pump, the special banjo fittings($$$) are NOT included. The one extra part to carry is a fuel pump, and the reasonably priced ones from ROCKAUTO workfine: https://www.rockauto.com/en/catalog/jensen,1974,healey,2.0l+l4,1312383,fuel+&+air,fuel+pump,6256
|
||||||||||||||
| |||||||||||||||
| Posted: 03-19-2018 05:59 pm |
|
4th Post |
|
redracer Member
|
btw, should have mentioned about rustproofing the car(floors, rockers, inner fenders) with POR15, Mastercoat, or KBS, all excellent products
|
|||||||||||||
| ||||||||||||||
| Posted: 03-19-2018 07:12 pm |
|
5th Post |
|
rbcnewfield Member
|
I did replace the fuel pump, I spent the money for a new brush-less SU. Also, I am rust proofing the floors as I go. Just fabricated a new rear seat support for the passenger side and then used a rust proofing paint. Attachment: 73 jensen project (35).JPG (Downloaded 151 times) Last edited on 03-19-2018 07:13 pm by rbcnewfield |
||||||||||||||
| |||||||||||||||
| Posted: 03-19-2018 07:19 pm |
|
6th Post |
|
redracer Member
|
Excellent; except I would have welded the seat channel in.
|
|||||||||||||
| ||||||||||||||
| Posted: 03-19-2018 07:24 pm |
|
7th Post |
|
rbcnewfield Member
|
I am adding more rivets. I thought about that but after looking at the spot welds there isn't a tremendous difference. Also, since the seat belts are mounted behind to the floor there is actually no pulling/lifting force ever really applied.
|
||||||||||||||
| |||||||||||||||
| Posted: 03-19-2018 07:45 pm |
|
8th Post |
|
redracer Member
|
Seat belts mounted to the floor? The original points of attachment were to the tm. tunnel and the side of panel welded to the rocker? There should be a large not welded in each spot(you can see the tm.' tunnel one from under the car)
|
|||||||||||||
| ||||||||||||||
| Posted: 03-19-2018 09:37 pm |
|
9th Post |
|
rbcnewfield Member
|
Yes, the tunnel. I was just pointing out the seatbelt is not attached to the seat.
|
||||||||||||||
| |||||||||||||||
| Posted: 03-26-2018 01:12 am |
|
10th Post |
|
rbcnewfield Member
|
More progress, Had the fuel tank cleaned and lined, refurbished the sender and installed the tank along with the new SU fuel pump. Now running off the tank. Attachment: 73 jensen project (38).JPG (Downloaded 124 times) Last edited on 03-26-2018 01:15 am by rbcnewfield |
|||||||||||||
| ||||||||||||||
| Posted: 03-26-2018 01:16 am |
|
11th Post |
|
rbcnewfield Member
|
Rebuilt the carbs this weekend, car runs well, next electrics and brakes. Attachment: 73 J-H CARBS.jpg (Downloaded 126 times) Last edited on 03-26-2018 01:20 am by rbcnewfield |
||||||||||||||
| |||||||||||||||
| Posted: 03-26-2018 01:21 am |
|
12th Post |
|
rbcnewfield Member
|
Installed factory air box set up from fellow member, Richard Zink, Thanks Attachment: 73 J-H air box.jpg (Downloaded 126 times) Last edited on 03-26-2018 01:22 am by rbcnewfield |
|||||||||||||
| ||||||||||||||
| Posted: 03-30-2018 01:28 am |
|
13th Post |
|
Jim Ketcham Member
|
Looks good. It looks like you still have the original radiator cap. You may want to replace that. Also, I don’t see the fan shroud. It makes a big difference with the original radiator and was put on by dealers after a TSB was issued. Good Luck, Jim
|
||||||||||||||
| |||||||||||||||
| Posted: 03-30-2018 11:25 pm |
|
14th Post |
|
rbcnewfield Member
|
Thanks for the advise. I am hoping to get it on the road the next few weeks. Just waiting for the rest of the snow to melt and some rain to fully wash off the roads.
|
|||||||||||||
| ||||||||||||||
| Posted: 03-30-2018 11:34 pm |
|
15th Post |
|
rbcnewfield Member
|
Making more progress, wheel cyl replace, brake fluid flushed, system bled. New tires mounted, wheels cleaned, now working on interior again. Floors painted, carpeting going in. Attachment: 73 J-H floor.jpg (Downloaded 93 times) Last edited on 03-30-2018 11:34 pm by rbcnewfield |
||||||||||||||
| |||||||||||||||
| Posted: 03-30-2018 11:35 pm |
|
16th Post |
|
rbcnewfield Member
|
More pics Attachment: 73 J-H FLOOR2.jpg (Downloaded 94 times)
|
|||||||||||||
| ||||||||||||||
| Posted: 03-30-2018 11:35 pm |
|
17th Post |
|
rbcnewfield Member
|
pic 3 Attachment: 73 J-H CARPET.jpg (Downloaded 92 times) Last edited on 03-30-2018 11:35 pm by rbcnewfield |
||||||||||||||
| |||||||||||||||
| Posted: 03-30-2018 11:36 pm |
|
18th Post |
|
rbcnewfield Member
|
sills Attachment: 73 J-H SILL.jpg (Downloaded 94 times) Last edited on 03-30-2018 11:36 pm by rbcnewfield |
|||||||||||||
| ||||||||||||||
| Posted: 03-30-2018 11:36 pm |
|
19th Post |
|
rbcnewfield Member
|
sill left Attachment: 73 J-H SILL2.jpg (Downloaded 92 times) Last edited on 03-30-2018 11:36 pm by rbcnewfield |
||||||||||||||
| |||||||||||||||
| Current time is 04:21 pm | |
| > Jensen Healey & Jensen GT Tech > Projects > 73 #11928 | Top |
