| ||||
> Jensen Healey & Jensen GT Tech > Body & interior stuff > convertible top installation instructions |
| ||||
> Jensen Healey & Jensen GT Tech > Body & interior stuff > convertible top installation instructions |
| Moderated by: Greg Fletcher |
|
||||||||||||||
| convertible top installation instructions | Rate Topic |
| Author | Post |
|---|
| Posted: 03-06-2019 04:12 pm |
|
1st Post |
|
Ralph H Member 
|
Hi All I have searched the site to no avail. Wondering if there is a best practice step by step directions sheet for new convertible top installation. Something with all the little tips and helpers to make the instal go smoothly. It looks pretty straight forward but that is what I thought when I tackled my MGA top a couple years ago.Turned out not to be as simple as it looks. Any help and direction appreciated. I stripped and cleaned and painted the roof bows and have a new top purchased from Martin Robey laid out and the fit looks good so far. cheers Ralph
|
||||||||||||||
| |||||||||||||||
| Posted: 03-06-2019 05:58 pm |
|
2nd Post |
|
redracer Member
|
post "convertible top" in the "Search" tab at the top for help. The glue we used for the front bow is 3M "Fast Tack Trim Adhesive", #08031(also used on sew-up bicycle tires). Home Depot used to carry the "80 spray can(not sure if they still do) which was also used. The main feature is being able to reposition it, unlike pure contact cement which can NOT have the item repositioned. When JENSEN was still in business, anew top from them came with the top already glued to a new front bow; I looked at all the tops I had from my cars(26+) to see where/how this was done. The part where the top meets the sew-on edges(triangular/pointed) goes right at the corner of the bow. You may have noticed the 2 pieces of the bow spot welded; I highly recommend you grind so the two pieces are smooth all around, especially at the 2 corners where the tops would usually get torn first.(I even glue a small piece here before I glued on the top, for added longevity). good luck, bruce
|
|||||||||||||
| ||||||||||||||
| Posted: 03-06-2019 06:02 pm |
|
3rd Post |
|
Ralph H Member
|
Thanks I searched with just the word convertible and got very little info adding the word top makes a huge difference
|
||||||||||||||
| |||||||||||||||
| Posted: 03-09-2019 07:06 pm |
|
4th Post |
|
Ralph H Member
|
Further to the top installation: Where does the fabric get trimmed along the front edge? I did not have any fabric on the frame when I got it so nothing to measure against. I have it glued on the curved top and around underneath already. But I have enough fabric to cover further on the wide flat section where the locking pins come thru and even enough to wrap around the thin edge and tuck the end out of sight. and there was a thin foam piece 3/4 inch wide where does this fit into the picture. Any help appreciated. Ralph
|
|||||||||||||
| ||||||||||||||
| Posted: 03-09-2019 07:21 pm |
|
5th Post |
|
redracer Member
|
a photo would be helpful; but the front edge gets trimmed at the first 90 degree face so that when a rubber seal goes on it would hide the remaining part(it does NOT go down to the second 90 degree edge(just before the face that has the 2 locking levers)
|
||||||||||||||
| |||||||||||||||
| Posted: 03-09-2019 07:23 pm |
|
6th Post |
|
redracer Member
|
btw, i do NOT use the hollow rubber bulb that came originally on the car as it does not keep the rain from coming in especially at the center(lock the front bow down and you will see a large gap in the middle when compared to the ends)
|
|||||||||||||
| ||||||||||||||
| Posted: 03-09-2019 07:30 pm |
|
7th Post |
|
Ralph H Member
|
thanks Redracer It (the top) is covered in clamps as the glue dries right now. your explanation is perfectly clear. I have already glued it to the second 90 degree tiny downward slope and I initially though I would trim it there and not take it onto the face with the locking levers. but there is lots of fabric so would this be a problem to cover that surface also? I think it would look nice.
|
||||||||||||||
| |||||||||||||||
| Current time is 07:31 am | |
| > Jensen Healey & Jensen GT Tech > Body & interior stuff > convertible top installation instructions | Top |
