| ||||
| ||||
| Moderated by: Greg Fletcher |
|
||||||||||||||
| Instrument Cluster Finisher | Rate Topic |
| Author | Post |
|---|
| Posted: 12-22-2018 11:25 pm |
|
1st Post |
|
JPJH Member
|
I've been hunting endlessly for a good substitute to the Chrome Finisher that goes around the instrument cluster. This is the part that is typically stapled in. I had ordered a replacement from the UK, but that really didn't fit, at all. Recently I came across a small 5MM Chrome strip that really looks like it would be a great replacement. The Chrome is attached to a very thin tapered plastic so it fits into the gap. I'm going to test using some 3M automotive tape. I cut a small sample of the Chrom strip and placed on my cluster, pictures attached. Attachment: JH Finisher 1.jpg (Downloaded 176 times)
|
||||||||||||||
| |||||||||||||||
| Posted: 12-23-2018 08:17 am |
|
2nd Post |
|
Frank Schwartz Member
|
My daughter,Patten Laurel, can sew you some silver braid in a clear plastic strip for a very nominal sum. You will need to remove the ten thousand micro staples that held the old strip around the bezel. I then use some very good contact cement to hold the new strip in place..... She has done a number of these for some of the Jensen Folk. You can reach her by email at patten1955@gmail.com Frank Schwartz
|
|||||||||||||
| ||||||||||||||
| Posted: 12-23-2018 08:20 am |
|
3rd Post |
|
Frank Schwartz Member
|
Correction: the correct email is patten1955@hotmail.com Frank P.S. I was having a senior moment....
|
||||||||||||||
| |||||||||||||||
| Posted: 12-23-2018 03:18 pm |
|
4th Post |
|
noomg Member
|
JPJH, MacGregor in Canada lists that chrome finisher part for 7 or 8 bucks. I've ordered other parts from them and been pleased with the quality.
|
|||||||||||||
| ||||||||||||||
| Posted: 12-24-2018 02:03 pm |
|
5th Post |
|
Brett Gibson JH5 20497 Member
|
I tried to buy in and was told no longer available, plus there on line pricing is 10 years old. Brett
|
||||||||||||||
| |||||||||||||||
| Posted: 12-25-2018 04:29 pm |
|
6th Post |
|
JPJH Member
|
Hi All, Thank you for the additional feedback. I also tried MacGregor's and should have mentioned initially the item was NLA. For this product, I installed the trim strip using 1/4" 3M automotive trim tape and a little clear adhesive around the corners. I installed the new finisher lines along the original's lines. As part of this work, I also freshened the gauges, cleaned the glass, new gaskets and added chrome surrounds to make the old Smiths look a little nicer. Attachment: Cluster 3.JPG (Downloaded 141 times) Last edited on 12-26-2018 02:45 pm by JPJH |
|||||||||||||
| ||||||||||||||
| Posted: 12-25-2018 04:32 pm |
|
7th Post |
|
JPJH Member
|
Here's another picture of the corner area Attachment: Cluster 2.JPG (Downloaded 141 times)
|
||||||||||||||
| |||||||||||||||
| Posted: 06-09-2019 05:19 pm |
|
8th Post |
|
rschlemm Member
|
looks great, where did you get the chrome surround material. Also like the chrome surrounds on the instruments as this dresses up the dash nicely....source for these
|
|||||||||||||
| ||||||||||||||
| Posted: 12-08-2019 04:13 pm |
|
9th Post |
|
mtechwim Member
|
I think it looks Great to. Where do the Chrome rings come from?
|
||||||||||||||
| |||||||||||||||
| Current time is 05:07 am | |
| > Jensen Healey & Jensen GT Tech > Body & interior stuff > Instrument Cluster Finisher | Top |
