| ||||
> Jensen Healey & Jensen GT Tech > Body & interior stuff > JH- Door Hinge Removal - Giant Phillips Head Screws |
| ||||
> Jensen Healey & Jensen GT Tech > Body & interior stuff > JH- Door Hinge Removal - Giant Phillips Head Screws |
| Moderated by: Greg Fletcher |
|
||||||||||||||
| JH- Door Hinge Removal - Giant Phillips Head Screws | Rating: 
|
| Author | Post |
|---|
| Posted: 10-23-2008 02:12 am |
|
1st Post |
|
Triplesn8s Member
|
Hi All, I am going to take the doors of the shell tonight but am immediately stymied by the Phillips head screw holding the hinges to the body. The hinges are in great shape but maybe they never go bad in which case I would just let them go with the shell. Should I try to save the hinges? Any tips on removing these screws without resorting to the drill? Bill
|
||||||||||||||
| |||||||||||||||
| Posted: 10-23-2008 02:57 am |
|
2nd Post |
|
JodyFKerr Member 
|
Those "big screws" are #3 phillips head. Don't bother with a screwdriver. If you've got some old-school tools out in the garage, see if you have an impact driver (It's a hammerable cylinder that rotates the screw head with impact). I often find that these old tools work best on old cars. :) If that doesn't work, try an electric impact driver. Modern version of above. If you don't want to wreck the whole thing, you can detach the hinge at the door instead. Those are (iirc) 13 mm bolts. That also gives you much better access to the screws. Jody
|
|||||||||||||
| ||||||||||||||
| Posted: 10-23-2008 03:01 am |
|
3rd Post |
|
Art DeKneef Member
|
About half of mine I was able to loosen with just a large screwdriver and muscle. This was after spraying some Kroil on the screws. The remaining ones I used one of those hand-held impact drivers. It had a large Philips bit included and after a few hits from the hammer they were able to be loosened with the large screwdriver.
|
||||||||||||||
| |||||||||||||||
| Posted: 10-23-2008 03:35 pm |
|
4th Post |
|
colinw59 Member 
|
On 15851 I had to resort to using an impact driver preceeded by some WD40. Some came out easily, while others offered a lot more resistance and finally relented after a stern talking to! When I put the car back together I located some coutersunk allen screws and used those (along with a lot of anti seize) instead of the old philips type. Not that I ever expect to take them out again! Good luck, Colin http://jhppg.com/gallery/74-Jensen-Healey-15851
|
|||||||||||||
| ||||||||||||||
| Posted: 12-05-2018 01:27 am |
|
5th Post |
|
noomg Member
|
Bill, I assume since it's been ten years since your original post one way or another you've solved your problem. For those who may run into this problem in the future there's a relatively simple way to solve this problem. Find a Phillips screwdriver that fits the screw and a hand sledge, spray the screws with a penetrant, center the screwdriver in the screw, whack it a few times, that usually takes care of the problem. I did this just recently on my J-H, it also worked on my Austin-Healey.
|
||||||||||||||
| |||||||||||||||
| Posted: 12-05-2018 06:35 pm |
|
6th Post |
|
redracer Member
|
Those are #4 cross point screws that take a #4 pozidriv screwdriver bit. A hand impact driver with a #4 regular Phillips bit will work fine. You will find much use for the hand impact driver(try to get the 3/8" one and not the larger 1/2" one) especially with the many #2 & #1 pozidriv screws. The bits can be found online(Google it) with the really tough ones(I highly recommend) coming from Germany, such as WERA, and WIHA(excellent quality)
|
|||||||||||||
| ||||||||||||||
| Current time is 12:04 pm | |
| > Jensen Healey & Jensen GT Tech > Body & interior stuff > JH- Door Hinge Removal - Giant Phillips Head Screws | Top |
