| ||||
> Jensen Healey & Jensen GT Tech > Body & interior stuff > Measure twice, glue once - lesson learned on door panels |
| ||||
> Jensen Healey & Jensen GT Tech > Body & interior stuff > Measure twice, glue once - lesson learned on door panels |
| Moderated by: Greg Fletcher |
|
||||||||||||||
| Measure twice, glue once - lesson learned on door panels | Rate Topic |
| Author | Post |
|---|
| Posted: 08-27-2008 01:20 am |
|
1st Post |
|
JodyFKerr Member 
|
Every once in a while I start to believe that I know what I'm doing, and that's inevitably when I screw up in the most colossal fashion. I just finished up redoing my door panels and they look beautiful. I went to install them in the car today only to learn something that I should have done at the beginning and neglected to do. And damn it, I should know better. So, here's my caveat to folks looking to recover their door panels... There is a piece of bent aluminum that glues to the top of the door panel. It's used to hook the top of the panel over the top edge of the door. *Before* you glue this piece to your door panel make sure that you test fit it on the door first! I glued mine 1/4" off and it means that the door panel will not fit. Worst of all, I can't cleanly modify what I've made, so it's a matter of starting over from scratch. At least the parts weren't expensive, but man, there was at least 40 hours in planning, thinking, cutting, gluing and doing on this. And it hurts to go back to scratch. Jody
|
||||||||||||||
| |||||||||||||||
| Posted: 08-27-2008 02:57 am |
|
2nd Post |
|
John Finch Member
|
Jody, I am sure a lot of us relate to your "oversight". I know I do. Been There Done That on several occasions! Thanks for the update.
|
|||||||||||||
| ||||||||||||||
| Posted: 08-27-2008 04:52 am |
|
3rd Post |
|
dwalls1 Member
|
Hang in there Jody! Like John said we've all BTDT.
|
||||||||||||||
| |||||||||||||||
| Posted: 08-28-2008 12:24 pm |
|
4th Post |
|
Jay Member 
|
I'm just now in the process of building new door panels myself. I will heed your warning. I plan to test fit the bare board with the metal attached before I apply the covering. On this subject: I do not have one of the inside lock knobs (small gray plastic slider). Does anyone have any suggestion of a suitable replacement for the manual lock slider knob and/or the entire knob and it's surround assembly. I know that I could just eliminate it, but I would rather have the inside lock option to keep things somewhat original. I was thinking of fabricating something out of wood or plastic. Any sugggestions would be most welcome. Jay
|
|||||||||||||
| ||||||||||||||
| Posted: 08-28-2008 02:58 pm |
|
5th Post |
|
JodyFKerr Member
|
The lock slider itself is available from Delta motorsports. As to the trim ring (escutcheon) and retaining plate (escutcheon plate) are NLA and can be hard to find. Jody
|
||||||||||||||
| |||||||||||||||
| Posted: 08-28-2008 04:28 pm |
|
6th Post |
|
Mitch Ware Member 
|
I didn't even bother putting the interior door locks on my doors when I redid them. I can't think of a time when I would ever use them. Mitch Ware - #19670 Attachment: Seat 7 (Small).JPG (Downloaded 76 times)
|
|||||||||||||
| ||||||||||||||
| Posted: 08-28-2008 07:57 pm |
|
7th Post |
|
dwalls1 Member
|
Hey Mitch, where did you get the lovely tan top cover? Was it custom made, or off the shelf? Once had a fellow tell me the top (hood) cover was part of the interior and should match it.
|
||||||||||||||
| |||||||||||||||
| Posted: 08-29-2008 12:56 pm |
|
8th Post |
|
Mitch Ware Member
|
I got that from DMS. It is closer in color to the original interior than it is to the tan interior I put in the car. But it is close enough that it looks right. Mitch Ware - #19670
|
|||||||||||||
| ||||||||||||||
| Posted: 02-19-2009 04:04 pm |
|
9th Post |
|
JodyFKerr Member
|
So, I finally got my doors done a while back. They look great and only took two tries. ;) I wrote up a how to article. http://www.theymightberacing.com/Projects/FrameOff/JH74G/DoorPanelRestoration.aspx
|
||||||||||||||
| |||||||||||||||
| Current time is 03:13 am | |
| > Jensen Healey & Jensen GT Tech > Body & interior stuff > Measure twice, glue once - lesson learned on door panels | Top |
