| ||||
| ||||
| Moderated by: Greg Fletcher |
|
||||||||||||||
| Rack and Pinion | Rate Topic |
| Author | Post |
|---|
| Posted: 09-25-2022 02:31 pm |
|
1st Post |
|
jomac Member
|
Has anyone adjusted the pinion gear preload. my steering has a slight play while driving. I checked out the steering shaft u joints they are ok. my play is at the rack and pinion gears. some Rack and pinion steering have an adjustment nut to change the preload between the 2 gears. Looking for how to adjust the Jensen Healey mark 1 or 2 RP steering?
|
||||||||||||||
| |||||||||||||||
| Posted: 09-25-2022 04:35 pm |
|
2nd Post |
|
redracer Member
|
Shims were used for the adjustment. If you pull off the top cover, you will probably have one or two shims under it. Suggest adding Dow Corning's M Gear Guard for added wear protection.
|
|||||||||||||
| ||||||||||||||
| Posted: 09-25-2022 10:07 pm |
|
3rd Post |
|
jomac Member
|
Redracer, I have not done this before can you explain more. Do I add more shims or place them elsewhere? What is the lower plate for? What adjustments are provided there? Ps. You rebuilt my water pump several years ago. Still working well. Thanks
|
||||||||||||||
| |||||||||||||||
| Posted: 09-26-2022 04:07 pm |
|
4th Post |
|
redracer Member
|
The top cover(2 1/4" bolts) has shim(s) under it to force/push the pinion gear down onto the rack. This is also where you would add fluid after changing broken rubber boots. I do not know where shims are available, but maybe a machine shop can help if you need any.
|
|||||||||||||
| ||||||||||||||
| Posted: 09-26-2022 06:38 pm |
|
5th Post |
|
jomac Member
|
Redracer Thanks for the info, I'll make a shim if necessary. But one question , when I lift off the top plate is there anything spring loaded ? Just don't want a surprise and loose a part. Regards
|
||||||||||||||
| |||||||||||||||
| Posted: 09-26-2022 07:27 pm |
|
6th Post |
|
redracer Member
|
Nothing to really "surprise" you, but yes there is a spring that pushes down on the special machines metal part that engages the pinion shaft. You can use needle nosed pliers or tweezers to pull that part out to give you an idea of how it works. You would also pull that part out if you plan to add oil/MoS2/whatever.
|
|||||||||||||
| ||||||||||||||
| Posted: 09-27-2022 08:47 pm |
|
7th Post |
|
jomac Member
|
After trying a tighter tolerance fit to pinion, it made no change in the play, but after a closer look found the movement is coming from the lower steering u joint. Order one from martinrobey.com. The upper steering shaft and u joint are in good condition That leaves only the column bushing at the firewall. I Hope that is not it , looks like a bear to service.
|
||||||||||||||
| |||||||||||||||
| Posted: 09-28-2022 01:24 am |
|
8th Post |
|
redracer Member
|
The standard test for determining play in the shaft is to LIGHTLY move the steering wheel(maybe by a friend of your arm isn't long enough) and visually look at the U joints, both upper and lower. The firewall bushing from the factory is a cheap piece of leather inserted into a sleeve--absolute rubbish. DELTA sells a perfect replacement in neoprene which MUST have the silicone lube supplied with it shmeared onto it, or it will "squeak" forever
|
|||||||||||||
| ||||||||||||||
| Posted: 09-28-2022 02:04 am |
|
9th Post |
|
jomac Member
|
Redracer How do you replace the steering bushing at the firewall? I can't see it from under the hood.
|
||||||||||||||
| |||||||||||||||
| Posted: 09-28-2022 02:16 am |
|
10th Post |
|
redracer Member
|
You need to remove the steering wheel, then the 4 cross point screws(#2) holding the aluminum bearing. Then loosen the upper steering shaft U-joint(just in front of the firewall) so you can pull the collapsible shaft up through the interior compartment. While you have this out, it would be a good idea to redo the nylon upper shaft "break" pins, since they are likely already broken(use the SEARCH box in the JHPS site forthis)
|
|||||||||||||
| ||||||||||||||
| Posted: 09-28-2022 12:13 pm |
|
11th Post |
|
jomac Member
|
Redracer Thanks , also, would you know the i.d. of the bushing that you used. I believe its 5/8 " , but not sure. My thought is to replace that bushing with a 2 bolt flangette ball bearings setup? Fastened to the firewall.i think there's room . Your thoughts on this idea? Regards
|
||||||||||||||
| |||||||||||||||
| Posted: 09-28-2022 01:30 pm |
|
12th Post |
|
redracer Member
|
Sorry--forgot to mention the original bushing has leather for the bearing surface. DELTA sells VERY nice neoprene ones and include silicone paste which MUST be applied or the shaft will squeal .
|
|||||||||||||
| ||||||||||||||
| Current time is 04:03 am | |
| > Jensen Healey & Jensen GT Tech > Miscellaneous > Rack and Pinion | Top |
